Audio terminal. Installed in homes, it allows communication with the entrance panel and door opening. A new concept of home phone. An integrated design, in line with new trends and lifestyles, simple and functional that combines quality and design. Its purity of lines, its technology and benefits make this equipment an elegant and perfect element for any home.

Device that allows to regenerate the Duox signal in both directions, isolate sections of the installation, as well as extend distances and terminal capacity. Input and outputs are isolated, against short circuits, load and signal reflections. It has 1 Entrance and 1 Exit. The sections on both sides require their own power set (“filter + source”): the 1-output regenerator amplifies the data, but does not let the power through. Recommended use: extend distances, increase number of terminals, isolate segments of the installation, isolate cable section changes in the same segment. Small in size, they can be installed in electrical registers. They can be screwed directly to the wall.

The DUOX trunk shunt is an intermediate device in a DUOX installation whose main functions are to isolate, distribute, regenerate and feed trunks in the installation. If a fault occurs in a trunk or in the input, due to a short circuit in the bus, or due to a data failure, it does not affect each other. Likewise, it is not strictly necessary to put a power supply at the outputs of each of the trunks since the device is capable of supplying said trunks (respecting the maximum loads).

The DUOX Relay allows a potential-free relay to be available in DUOX installations, with several configurable modes of operation and activation: (1) Activation of the relay by means of commands generated from the house terminals, boards or guard units. (2) External activation by push buttons, additional external switches, etc ... The DUOX Relay can be installed anywhere on the duox bus. It is possible to install one or more relays: per apartment, block or installation. Input voltage: 18 VDC.

Increase the level of call volume in facilities with a large number of telephones or monitors in the same home (more than 5).

Changing tables are required in installations with more than one access. Its function is to connect the telephone or monitor of the house with the plate from where the call is being made. Maximum 7 accesses. 1 changing table is required for each door entry / video door entry access. Only in case of 2 accesses 1 changer is needed. There are two models that depend on the type of additional access: doorman or video door entry. DIN-10 rail format to facilitate installation inside an electrical equipment box, or they can be screwed directly onto the wall.

They are user identification devices with unique identifiers. Each device is marked with the identifier to register it in the system. The identifier is encrypted to prevent copies from being made with the intention of fraudulent use. Does not require maintenance or batteries. Includes magnetic stripe for additional function.

They are user identification devices. Each device is marked with the identifier to register it in the system. Does not require maintenance or batteries. Credit card format. White PVC material. They can be personalized with logos and user photos using a sublimation printer.

They are user identification devices. Each device is marked with the identifier to register it in the system. Does not require maintenance or batteries.

USB desktop reader for reading both EM 125KHz cards and key fobs. It facilitates the management of registrations of this type of identifiers through a PC, without having to go to the installation reader. Once the drivers are installed with the reader connected, the corresponding registration management software must be run (AC+, MDS, LYNX, etc ...). After clicking in the card registration field, press F8 to display the card code that we have just presented to the reader.

230VAC FERMAX® Power Supply for 2 Wire Audio CITY ™ Kit. DIN6 rail installation.

Door release buttons are the most common and the most frequently used in the access control systems. Mainly used by public institutions, banks, large, small and medium-sized enterprises, stores and residences. Stainless steel Panel with Elegant Style. 500.000 Cycles tests. Three Contact Output. Suitable for all kinds of Locks Releases.

The FPAC-MAX is a biometric fingerprint reader equipped with a high-quality optical sensor and ISO / IEC 14443A and MIFARE® proximity reader. Users can be recognized by comparing their fingerprint with those registered in the reader's memory (1: N mode) or with those registered on the MIFARE® card (1: 1 mode). The reader can store up to 1,900 fingerprints and is still able to recognize users relatively quickly. If the 1: 1 mode is applied, the third level of recognition (the highest) is applied and maximum privacy is achieved.

CITY-DUOX Doorphone Kits incorporate the latest digital technology from FERMAX. DUOX is the new digital system that represents a technological and innovative leap in the market. It only requires two non-polarized cables for: power, audio and data transmission. Includes: 70704.- CITY DUOX 1/L plate. S1 plate: 130x128mm. 8948.- S1 kit embedding box: 115x114x45mm. 3430.- iLOFT DUOX telephone. 4810.- 18VDC/1,5A-12VAC/1,5A power supply. DIN10. 3244.- DUOX filter.

CITY-DUOX Doorphone Kits incorporate the latest digital technology from FERMAX. DUOX is the new digital system that represents a technological and innovative leap in the market. It only requires two non-polarized cables for: power, audio and data transmission. Includes: 54334.- MARINE DUOX 1/L plate. ST1 plate: 150x180mm. 4641.- Marine ST1 embedding box: 130x160x55mm. 3430.- iLOFT DUOX telephone. 4810.- 18VDC/1,5A-12VAC/1,5A power supply. DIN10. 3244.- DUOX filter.

BUSing power supply capable of delivering 500 mA. It allows supplying power to the rest of the equipment connected to the BUS.

BUSing power supply capable of delivering 1000 mA. It allows supplying power to the rest of the equipment connected to the BUS.

500mA BUSing power supply with external battery connection (not included).

Regulator for 0-100% lighting control with 1-10V control.

One channel lighting regulator with a maximum of 200 W. Equipment indicated for LED lighting, although it also allows any type of incandescent or halogen lighting, whether or not preceded by transformers (except electromagnetic). Installation in registry.

Two-channel lighting controller with a maximum of 200 W per channel. Equipment indicated for LED lighting, although it also allows any type of incandescent or halogen lighting, whether or not preceded by transformers (except electromagnetic). DIN rail installation.

IP fingerprint reader with integrated MIFARE proximity. You can work both independently and centrally. Manages 5,000 users per reader. Stores 200,000 events per reader. It is necessary to add a relay ref. 2013 for the connection of electric openers. Maximum 150 readers on the same ethernet network. Fingerprints can be registered on one of the readers manually and then from a USB stick, clone the information to the rest of the readers. All readers must have the same ID (reader number). By default they come out as 1. The format of the wiegand reader has to be in 34_MI. It also has free software (INKEY-MINI) available on our website, which allows users to receive these users and transfer them to the rest of the readers via IP, or even through a USB desktop reader ref. 5234 register the fingerprints in the software and transfer them to all readers. For this, each fingerprint reader must have a different ID (reader number) and it must have the wiegand format configured as WIEGAND 34_MI.

Internal connection cable for IP_Axes system, for compatibility with CITY, MARINE and SKYLINE readers.

Access control reader with double technology: proximity and keypad, on the same board. Independent or joint operation for greater security. (1) Independent operation: (1.1) Proximity, which allows the door to be opened by approaching a proximity card or key fob. (1.2) Keypad, which allows the door to be opened by entering a previously programmed code of up to 6 digits. (2) Joint operation for greater security: card + PIN code. (2.1) Reader that allows the door to be opened by approaching a proximity card or keyfob + a 4-digit PIN code. (2.2) Proximity reader that by means of a dipswitches configuration (SW2) that it incorporates can work in an autonomous or centralized system. OPTION 1: Configuration as CENTRALIZED MDS-AC Plus. OPTION 2: Configuration as CENTRALIZED with Wiegand 26 protocol. Frequency: 125kHz.