Multisensor detector with double technology, of smoke and heat, made by AGUILERA™ ELECTRÓNICA according to UNE EN 54-7 and UNE EN 54-5 standards with CE certificate of conformity and AENOR quality mark. addressable algorithmic unit that manage a optic smoke sensor and other of heat. The optic sensor take light measure that disperse smoke particles and its raise. All measurements are analized and sended to the central to take a alarm decision that always reaches the programmated parameters. Possess the same features than AE/SA-OP detector.

Outdoor sounder with LEDs luminous indications. Protection: IP54. Dimensions: 210 x 230 x 60 mm. Weight: 1.10kg. Power supply: 12-30VDC. Acoustic power: 95dB at 1meter, Frequency: 3.1-3.8Khz. Temperature range: -40ºC to 85ºC.

Unit developed and made by AGUILERA™ ELECTRÓNICA through UNE EN54-2 standards to control fires, technical signals and other parameter changes which occur in mobile phone booths and similar facilities. Contains a stabilized power supply, powered at 230 V with input protections, 27 and 12 VDC outputs and a battery charger. Monitored loop which controls a detector and fire switches zone, with signaling of: 1st level of fire, 2nd level, breakdown and service. Monitored loop for automatic fire extinction, programmable to release the extinguishing agent with the 1st or 2nd fire level. Relays: for fire, general breakdown supervised, air conditioned pause and repetition of external alarms, 1 and 14. Controls from 14 to 30 depending on the model. These inputs are individually selectable by contact, normally open or closed, which are transmitted by sub D37 pin connector ( 2A relay outputs, voltage free by individually selectable contact, open or closed). Measures: 375 x 280 x 130 mm.

Unit developed and made by AGUILERA™ ELECTRÓNICA through UNE EN54-2 standards to control fires, technical signals and other parameter changes which occur in mobile booths and similar facilities. Contains a stabilized power supply , powered at 230 V with input protections, 27 y 12 VDC outputs and a battery charger. Monitored loop which controls a detector and fire switches zone, with signaling of: 1st level of fire, 2nd level, breakdown and service. Monitored loop for utomatic fire extinction, programmable to releas the extinguisher agent with the 1st or 2nd fire level. Relays: for fire, general breakdown supervised, air conditioned pause and repetition of external alarms, 1 and 14. Controls from 14 to 30 inputs depending on the model. These inputs are individually selectable by contact, normally open or closed, which are transmitted by sub D37 pin connectors (2A relay outputs, voltage free by individually selectable contact, open or closed). Measuress: 375 x 280 x 130 mm.

Phone dialer for conventional telephone line, that connected with our algorithmic panels, allows you to received text notifications about installation status in a phone. Dispose of severals zone control inputs, as well as programmable outputs for remote uses, such as replace of the panel, activate or desactivate devices.

Push button protector for outdoor areas, compatible with AE/SA-PT and AE/V-PSAT models.

Design to indicate the alarm status in visble place of one or more detectors installated in hidden places. Its standard location is on interior doors. Use a built-in box with standard mechanism, 2W lamp, red optic indicator and white ABS trim. Dimensions: 85 x 85 mm. Consumption: 95mA to 24V.

Wall mounting, made in white ABS provided with two high luminosity LEDs. Visible from both sides of corridors. Dimensions: 70 x 50 x 25 mm. Consumption: 35mA to 24V.

Panel made by AGUILERA™ ELECTRÓNICA composed by 32 light indicators for representation in real time of installation status, and FULL-DUPLEX intercommunication between the repeater panel and the fire panel. Ideal for nurses positions and other monitoring zone.

Low consumption multi-tone sounder. Certified in accordance with EN54-3. Consumption between 6 and 33mA, in function of the tone. Sound power: 102dB (Tone3). Includes a microprocessed module for its direct integration in the algorithmic loop. Dimensions: Ø 93 mm, height: 63mm. Includes high base.

Switched short-circuit protected protected power supply at 24VDC/2A made according to EN54-4 standard. Input 230/115VAC; 50/60Hz. LED indications for general status, battery charging and output fuses according to EN54-4 standard. With 2 independent outputs protected against short-circuits. Equipped with a microprocessor card for permanent state monitorization. Capacity for 2 (two) 12V/17Ah batteries. Dimensions: 320 x 272 x 125 mm.

Switched short-circuit protected protected power supply at 24VDC/2A made according to EN54-4 standard. Input 230/115VAC; 50/60Hz. LED indications for general status, battery charging and output fuses according to EN54-4 standard. With 2 independent outputs protected against short-circuits. Equipped with a microprocessor card for permanent state monitorization. Capacity for 2 (two) 12V/17Ah batteries. Dimensions: 320 x 272 x 125 mm.

Switched short-circuit protected protected power supply at 24VDC/2A made according to EN54-4 standard. Input 230/115VAC; 50/60Hz. LED indications for general status, battery charging and output fuses according to EN54-4 standard. With 2 independent outputs protected against short-circuits. Equipped with a microprocessor card for permanent state monitorization. Capacity for 2 (two) 12V/17Ah batteries. Dimensions: 272 x 320 x 125 mm.

Switched short-circuit protected protected power supply at 24VDC/5A made according to EN54-4 standard. Input 230/115VAC; 50/60Hz. LED indications for general status, battery charging and output fuses according to EN54-4 standard. With 2 independent outputs protected against short-circuits. Equipped with a microprocessor card for permanent state monitorization. Capacity for 2 (two) 12V/17Ah batteries. Dimensions: 390 x 440 x 100 mm.

Switched short-circuit protected protected power supply at 24VDC/5A made according to EN54-4 standard. Input 230/115VAC; 50/60Hz. LED indications for general status, battery charging and output fuses according to EN54-4 standard. With 2 independent outputs protected against short-circuits. Equipped with a microprocessor card for permanent state monitorization. Capacity for 2 (two) 12V/17Ah batteries. Dimensions: 440 x 390 x 100 mm.

Protective cover with tamper-proof design to avoid false alarms. Made in transparente polycarbonate resistant to temperature between -40ºC and +49ºC. Easy installation.

TCP Network card for connection of algorithmic panels in Ethernet networking TCP/IP 10/100 Mbps. The card is housed inside the panel. For AE/SA-C1.

TCP Network card for connection of algorithmic panels in Ethernet networking TCP/IP 10/100 Mbps. The card is housed inside the panel. For AE/SA-C2 and AE/SA-C8.

Multiprotocol module that allows the integration of AGUILERA™ ELECTRÓNICA algorithmic panels in differents control systems. protocols supported: Modbus RTU, Modbus TCP, N2 de Metasys OPTIMUS and ESPA 4.4.4. Dimensions: 105x75x30mm. Dispose of several interfaces: RS232, RS485, Ethernet.

System that allows the control and remote management of fire detection installations. Telecontrol system of AE/SA-TC installations gaves important benefits in new installations, as well as the maintenance of service device. The system allows distance controlling of any installation, based in analogue or algorithmic SA series panels. Composed by AGE44 control software that allows to control the panel connected and makeing any action over the system. It is specially recommended for installations that requires a scheduled remote control from a different location. For exemple, night watchman.

Remote control terminal made by AGUILERA™ ELECTRÓNICA, provide remote control and managment of fire protection installations based in their algorithm centrals. This terminal permit aloof control by cable (RS-485) any installation based in AE/SA-C1, AE/SA-C2 and AE/SA-C8 centrals. Network connection, through RS-485 communication channel. All control panels shows general status of all existing centrals in the network. Provided with independent power supply and capacity for two 7Ah batteries. Dimensions: 410 x 310 x 120 mm.

Microprocessed temperature detector that programmed from the control unit controls the temperature parameters in two levels: Differential and thermal. The thermal detectors are specially designed for those places where the fire starts with sudden rises in temperature or where smoke detectors are not recommended due to the existence of combustion gases in the environment.

Heat detector made by AGUILERA™ ELECTRÓNICA in accordance with UNE EN54-5 standard with CE certificate of conformity and AENOR quality mark. addressable algorithmic unit thant manage two temperature parameters: Differential and thermal. Both measure are analized and send to the central to take a alarm decision with the setting made in each case.

Design and made by AGUILERA™ Electrónica according to UNE EN54-5 standard. Certified by AENOR. Gives alarm signal when detects a sudden increase in temperature or when the increasment is very slow and reach the 58ºC. Provided of LED alarm indicator with electrical interlock , automatic check operation, voltage stabilizer and automatic alarm output to connect remote action indicators. Mounted in white ABS housing of 105 Ø x 45 mm high. Consumption: 50 ?A in standby and 22mA in alarm. Version with automatic resart.