3'' loudspeaker made of metal for 70 / 100V lines, Low loss transformer 6 / 3W @ 100V, 6 / 3W @ 70V. Frequency response: 90-18000Hz +/- 10dB, Sensitivity: 85 dB (1W 1m), Dimensions in mm (Diameter x depth) 104 x 90 mm. Color: RAL 9002.

Sphere speaker with line transformer 70 / 100V Power 16, 8, 4 W @ 100V 8,4,2W @ 70V Frequency Response 110-13,000 Hz Sensitivity 90 dB at 1 W / 1 m. Protection degree IP-35. Color RAL 9010 Dimensions: 185 mm (Ø) x 157mm. Cable 4.5 m.

System control and supervision system through Ethernet networks for voice evacuation functionalities. The system allows monitoring of the message and zone that is being activated at all times during an evacuation / alert process through the color coding of the zone button. The notification menu is included at the bottom of the interface through a dropdown. Completely independent VAP system for emergency management (redundancy of emergency operating position). It allows the emergency management of multiple NEO islands through ethernet communication, as well as supervision through direct monitoring of NEO equipment.

Filtered load impedance for improvement of loudspeaker line measurement accuracy on 70 / 100V lines. It allows to add precision to the connection integrity check between the speakers and the PA / VA system. It is a small device very easy to install and with a very low consumption. Multiple devices can be connected to the same line of speakers. Does not require return lines to the system.

Controller for 10 dimmer lines with remote control signal input for each line, 1 sub-D15 type control input, 1 RJ-45 type ethernet control input, 1 general dimmer activation input with loop-throw-output EUR type.

Allows you to send email notifications about SIME CONTROL and SIME CALENDAR. Requires internet connection on the server and use of external SNMP server. Delivery time 3 weeks

MODBUS Converter RTU-TCP/IP (1 per Panel)

1 for each installation, up to 16 centrals.

Plastic lid that makes it rearmable.

Glass spare parts for manual button (Pack of 5).

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Three programmable alarm relay outputs with different levels for each gas. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations. Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Three programmable alarm relay outputs with different levels for each gas. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations. Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Three programmable alarm relay outputs with different levels for each gas. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations. Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Three programmable alarm relay outputs with different levels for each gas. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations. Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of explosive gases with catalytic technology (pellistor), for a detection range of 0 to 100% L.I.E. and resistant to silicone vapors. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Especially suitable for use in laboratories or compartmentalized areas that, in addition to local use, need control and perform maneuvers and report their status remotely.

Autonomous programmable detector designed for the detection of explosive gases with catalytic technology (pellistor), for a detection range of 0 to 100% L.I.E. and resistant to silicone vapors. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Especially suitable for use in laboratories or compartmentalized areas that, in addition to local use, need control and perform maneuvers and report their status remotely.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations (STANDGAS O2 does not require this characteristic). Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations (STANDGAS O2 does not require this characteristic). Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations (STANDGAS O2 does not require this characteristic). Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations (STANDGAS O2 does not require this characteristic). Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations (STANDGAS O2 does not require this characteristic). Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations (STANDGAS O2 does not require this characteristic). Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations (STANDGAS O2 does not require this characteristic). Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.

Autonomous programmable detector designed for the detection of toxic gases and O2 with electrochemical technology and CO2 with infrared technology. Provided with a backlit 16 X 2-line display, three keys, programmable alarm relay output and internal acoustics. Digital control over the state of the sensor. Automatic hardware status testing. Digital filter based on variable sampling of the averages of the sensor values. Automatic thermal compensation that provides a correct response to temperature variations (STANDGAS O2 does not require this characteristic). Exact automatic zero adjustment. Monitors zero relative to sensor and electronics response. STANDGAS automatically performs a test every 30 minutes: if the drift -drift- is greater or less than 2% of the total scale value, it will be reset to zero; otherwise the data will be displayed as a reading. Other functions only accessible at the factory allow knowing the remaining useful life of the sensor, the date of manufacture and the last calibration, in addition to the serial number.