Wiegand RF receiver with polycarbonate box, 30 BITS compatible with the full range of transmitters.

Wiegand RF receiver with polycarbonate box, 26 BITS compatible with the full range of transmitters.

RF 433 Mhz receiver with Wiegand output, in polycarbonate box compatible with the entire range of transmitters. Dimensions: 128 x 128 x 57 mm. Operating voltage: 12 / 24VAC / VDC. Range: Up to 100 meters in the open field. It has a memory of 50 codes.

RF receiver with Wiegand output of 26 or 30 bits. It has 4 memory locations to store up to 2 Facility Codes and 4 buttons, and also has an open memory of 4000 users. The process of registering new commands is very simple, since you only have to press the transmitter button 3 times within the range of the receiver.

A6U48 is a middle range high performance UHF RFID integrated reader. It supports fast tag read/write operation with high identification rate. It can widely applied in many RFID application systems such as logistics, access control, anti-counterfeit and industrial production process control system. The reader A6U48 generates continuously a RF signal in the band 865 - 868 MHz. When a passive tag ( card, sticker or car plate type ), carried by an user or fixed on a vehicle enters in the RF field, generated by the reader, a small perturbation occurs: the tag replies with an encrypted signal, that includes its s/n and more information. These are then detected by the reader which transmits the signal to the decrypting I/F device, that makes them available in wiegand format or activate a relay. The wiegand signal can be read by an Access Control System that gives the final authorization to the user. The reader comes with the corresponding I/F device which has a RF receiver built-in, operating at 433,92 MHz, with a memory for 100 remote controls. The remote control can be used as an alternative means of identification from longer range, with the very high security level given by the 128 bit rolling code, encrypted AES128.

A10U48 is a high performance UHF RFID integrated reader. It supports fast tag read/write operation with high identification rate. It can widely applied in many RFID application systems such as logistics, access control, anti-counterfeit and industrial production process control system.The reader A10U48 generates continuously a RF signal in the band 865 - 868 MHz. When a passive tag ( card, sticker or car plate type ), carried by an user or fixed on a vehicle enters in the RF field, generated by the reader, small perturbation occurs: the tag replies with an encrypted signal, that includes its s/n and more information. These are then detected by the reader which transmits the signal to the decrypting I/F device, that makes them available in wiegand format or activate a relay. The wiegand signal can be read by an Access Control System that gives the final authorization to the user. The reader comes with the corresponding I/F device which has a RF receiver built-in, operating at 433,92 MHz, with a memory for 100 remote controls. The remote control can be used as an alternative means of identification from longer range, with the very high security level given by the 128 bit rolling code, encrypted AES128 .

The receiver RXCP makes part of the system CDVI® Pass: a radio system for the access control of persons and vehicles based on radio active tags. The system is mainly composed by 3 devices: one or more active tag, one trigger antenna and one receiver. It finds application in domestic, pubblic, residential and industrial environment, both for personal and vehicular use. The users or the vehicles carrying the active card and standing in the detection zone of the trigger aerial, are identified waking-up the tag, which is normally in stand-by and decoding the tag information. The serial number of the tag, that identifies uniquely the user, is then transmitted via radio to the receiver, which, at its turn, sends the information to any access control system, through a bus RS-485 or wiegand line.

The 125KHz antenna is part of the CDVI® PASS system. It transmits periodically a trigger signal (with a period of 0,5 - 2,4 Sec) with a predefined pattern to awake the active cards. Each single transmission lasts 34ms. External inputs allow synchronization with other antennas (up to 4). When sync-in and sync-out are left open, the gap between two transmissions is 2.4 Sec. When shorted, it is reduced to 500mS. The enable input handles the transmission. Before each transmission, the system controls this input and if it is left open, the transmission is inhibited. Using the onboard rotary trimmer, it is possible to assign an ID (0-9) to the antenna to distinguish it from the other. Additionally, inputs for two PIR sensors are provided ( internal and external one) to awake the antenna only in presence of movement.

The trigger antenna AN02RCP transmits periodically a trigger signal (with a period of 0,5 - 2,4 Sec) at 125 KHz, with a predefined pattern, that awakes the active cards standing in the detection zone [0,3 - 6 m]. Once awakened, the card, at its turn, sends a signal at 433,92 MHz to the built-in receiver of the antenna. The receiver can activate directly a relay or send out on the bus wiegand the s/n of the tag, that can be managed by a further access control system. The memory of the built-in receiver can hold up to 500 cards. A 10-position rotary switch allows to identify each antenna with a unique number, included in the wiegand protocol ( 26,30 or 44 bits ). Each antenna can even be enabled by an external PIR ( not provided ).

The trigger antenna AN01RCP transmits periodically a trigger signal (with a period of 0,5 - 2,4 Sec) at 125 KHz, with a predefined pattern, that awakes the active cards standing in the detection zone [6 - 15 m]. Once awakened, the card, at its turn, sends a signal at 433,92 MHz to the built-in receiver of the antenna. The receiver can activate directly a relay or send out on the bus wiegand the s/n of the tag, that can be managed by a further access control system. The memory of the built-in receiver can hold up to 500 cards. A 10-position rotary switch allows to identify each antenna with a unique number, included in the wiegand protocol (26, 30 or 44 bits). Each antenna can even be enabled by an external PIR (not provided).

The trigger antenna AN01RCP transmits periodically a trigger signal (with a period of 0,5 - 2,4 Sec) at 125 KHz, with a predefined pattern, that awakes the active cards standing in the detection zone [6 - 15 m]. Once awakened, the card, at its turn, sends a signal at 433,92 MHz to the built-in receiver of the antenna. The receiver can activate directly a relay or send out on the bus wiegand the s/n of the tag, that can be managed by a further access control system. The memory of the built-in receiver can hold up to 500 cards. A 10-position rotary switch allows to identify each antenna with a unique number, included in the wiegand protocol (26, 30 or 44 bits). Each antenna can even be enabled by an external PIR (not provided).

Long range reader with Wiegand output, adjustable range up to 15 m, can read up to 20 cards simultaneously, surface mounting.

Enables reader adjustment of the uPASS™ Reach at the desired angle and direction to ensure reliable reading. The mounting set can also be used for mounting the reader to round or square masts.

Protects the uPASS™ Target from temperature rise by means of long lasting exposure to the sun.

External antenna for the uPASS Target reader. The combination (uPASS Target reader + uPASS™ Target Antenna) can be used to extend the read-range of the reader for a wider scope. Additionally, the external antenna can be used in situations where reading of both vehicle entry and exit lanes is required. The Wall Mounting Set (part number 9984364) is standard included.

High-end UHF reader for long-range identification up to 10 meters (33ft.) for demanding situations. The Wall Mounting Set (part number 9984364) is standard included. ISO 18000 EPC Gen2 compliant.

Pole mounting kit for uPASS™ REACH reader.

Pole mounting kit, including uPASS™ protection cover.

Swivel support for easy orientation, aluminum made. Only for the ENTRY ™ reader.

Additional protector for TRANSIT™ readers, for extreme climatic conditions. Compatible with wall and pole kits.

Pole mounting kit for TRANSIT™ readers. Galvanized steel suitable for cilindric poles or squares up to 190 mm (diameter( or 150 mm (side).

UHF (860 - 950 MHz) RFID reader, up to 2 meters range. Based on EPC GEN2 standar. Includes RS232 and 422 output for FIRMWARE and Wiegand 26 bits output directly.

UHF (860 - 950 MHz) RFID reader, up to 4 meters range. Based on EPC GEN2 standar. Includes RS232 and 422 output for FIRMWARE and Wiegand 26 bits output directly.

ISM (2446-2454 GHz) RFID reader, up to 4 meters range at 200 Km/h. Includes mounting wall kit, RS232 communications plate, and Wiegand 26 bits preconfigured protocol.