DC-9102E conventional photoelectric smoke detector is a new-generation product. With built-in microprocessor, the detector is highly fixed with reliable fire judging program, which make it stable and reliable performance. When the detector checks fire signal, it will send fire information to the control panel or addressable zone monitor unit by means of current changing. The detector keeps turning on the LED to indicate alarm state until it is reset. The detector is developed from sensing chamber by scattering theory. It has the ability to resist dust contamination and environmental light.

DC-9103E conventional rate of rise and fixed temperature heat detector is a new generation product of GST. With built-in microprocessor, it works stably by being fixed with highly reliable fire judging program. On detecting a fire signal, it can change its own current to transmit the signal to fire alarm control panel (FACP) or addressable zone monitor unit. The detector keeps illuminating fire LED until it is reset by power-down.

C-9404 Conventional Sounder is an audible alarm device used to warn people in field when fire occurs. It can give audible alarm signal when applied to external 24VDC power (D1 connected with positive and D2 with negative). A 25.5mm high shallow base and a 40mm high deep base are available.

C-9403 Conventional Sounder Strobe is an audible and visible alarm device used to warn people in field when fire occurs. It can give audible and visible alarm signal when applied to external 24VDC power (D1 connected with positive and D2 with negative). A 25.5mm high shallow base and a 40mm high deep base are available.

The C-9104 Conventional Ultraviolet Flames Detector senses the ultraviolet (UV) rays emitted by a burning substance and is used in areas where you would expect heat and smoke that would leave the usual option of heat or smoke detectors ineffective, such as generator rooms. Requires DZ-03 or DZ-03D mounting base.

Deep Base for surface mounting the GST souun nder and Sounder/beacon (addressable I-9403,I-9404and I-9407, CCo onventional C-9403 and C-9404).

Deep Base for surface mounting the GST souun nder and Sounder/beacon (addressable I-9403,I-9404and I-9407, CCo onventional C-9403 and C-9404).

DZ-03 Base is used to mount conventional and intelligent smoke, heat and combination detectors as their conductive base. It’s made of flame-resistant plastic ABS, which is a UL94 listed material. It features attractive appearance, novel structure and stable performance. Its flame class is V-0. During installation, you can easily fix the base before connecting cables, and then tw ist the detector onto the base.

DZ-03 Base is used to mount conventional and intelligent smoke, heat and combination detectors as their conductive base (C-9102, C-9103, I-9102, I-9103). It’s made of flame-resistant plastic ABS, which is a UL94 listed material. It features attractive appearance, novel structure and stable performance. Its flame class is V-0. During installation, you can easily fix the base before connecting cables, and then twist the detector onto the base.

Dual-band infrared light detection for fire alarm. Sensitive to flame from material containing carbon. Suitable for fire starting from flame in large indoor or outdoor areas. Addressable (connecting fire alarm control panel) and non-addressable (through relay contact) working modes optional. Flame-proof. Applicable to either commercial or hazardous industrial areas, such as explosive Zone 1 and 2, and Zone 21 and 22 with flammable dust.

Integration of the emitting and receiving part makes for easy installation and accurate optical pathway. Built-in microprocessor enables intelligent judgment of fire alarm and fault. Easy alignment ensures a single person installation. Self-diagnostic. Drift-compensation for factors weakness, such as dust contamination, positional excursion and component ageing. Integrated functions for both addressable and conventional use. Electrically address by handheld programmer. Fire and fault volt-free contact output for Integration of the system. 2 sensitivity levels can be set by programmer. SMT processing technology.

DI-9104Exd is a light-sensitive detector that detects fire by picking up the ultraviolet light from flaming material. It’s designed for areas where an open fire is liable to occur with large amount of radiation and no smoldering stage, or where quick response to a fire is required. This detector can be applicable to zone 1 and 2 of explosive areas. The detector is able to work either in addressable mode connecting with GST intelligent fire alarm control panel to transmit signal through detection loop or in non-addressable mode connecting to 24VDC power supply to transmit signal by outputting different resistance values.

Connecting to the loop of GST fire alarm system, DI-9204E Digital Manual Call Point (MCP) is suitable for public places. When there is a fire, pressing the frangible element on this MCP can send fire signal to fire alarm control panel. After receiving the signal, the control panel will show address information of the MCP and generate alarm sound.

Connecting to the loop of GST fire alarm system, DI-9204 Digital Manual Call Point (the MCP) is suitable for public places. When there is fire, pressing the action plate on the MCP can send the alarm signal to fire alarm control panel. After receiving the signal, the control panel will show address information of the MCP and generate alarm sound.

Input port monitored with 4.7K? EOLR. Normally open or normally closed contact acceptable. Electronically addressed. Addresses can be modified in field. Built-in microprocessor and AD sampling technology. Loop Powered. LED status indication. Din-Rail mount or surface mount. Standard: EN 54-18:2005. LPCB Approved.

C-9317 Emergency Gas Override Control is used to control the start and stop of gas extinguishing system. It's usually installed in areas to be protected. When fire occurs, pressing emergency start button, messages can be sent to gas extinguishing control panel, which will give gas extinguishing command and start the solenoid after delay. During the delay time, if the person in field can confirm there is no fire, he could press the emergency stop button. Operation Principle: Since the connected extinguishing control panel is able to check broken circuit and short circuit, the four states of short circuit, broken circuit, normal and alarm are distinguished by the loop resistance, which is 3k? in normal state, and 330? and 3k? in parallel when the button is pressed. Start output is by pulse mode and stop output is by electric level mode.

Fiber optic interface for GST-IFP8 control panels. For single-mode fibers, distance up to 25 kms.

The GST301 conventional gas extinguishing control panel is packed with unique features that you have come to expect from a GST product that have enabled us to become world recognized as a leading manufacturer in the fire detection industry. The system provides 3 fire detection zones, two of which are utilized for double knock gas extinguishing control, and a third Auxiliary fire detection zone for additional areas out side of the gas protected area. This Zone will operate as a normal fire detection zone and have no interaction with the gas release system. Primary and Standby cylinder key switch, that enables quick and easy transfer to the reserve cylinders, thus to ensure that the area can be left protected after an evacuation. The pre release gas countdown timer display on the panel to shows the amount of time left (in seconds) before the gas will be released, this is adjustable from 0- to 90 seconds, (all panels are sent factory set at 30 seconds delay).

C-9318 Gas Extinguishing Warning Indicator (hereinafter called the indicator) is the accessory equipment of a gas extinguishing system. It's usually installed at the entrance of the protected area. After gas is released, the control panel will activate the indicator to give visual indication warning people in field to take relative measures. This indicator is non-addressable and is used together with GST303/GST306 extinguishing control panel.

Free Download from Web. GstGMC Graphic Monitor Centre is a newly developed fire alarm system monitoring software. With friendly interface, the software may support 8 remote client stations plus local monitor station, making complete monitoring and control. Also with OLE for Process Control (OPC), the communication with fire alarm control panel?FACP? can also be integrated into other systems. The related FACP include GST200, GST200-2, GST5000 and GST-IFP8.

DI-9103E intelligent rate of rise and fixed temperature heat detector is a new addressable fire alarm device cooperating with GST intelligent fire alarm control panels(FACP) to build a fire detection system. The detector shows fire alarm by the LED indicator and transmits the signal to the FACP.

DI-9101E intelligent combination heat photoelectric smoke detector integrates photoelectric detection and fixed temperature and rate of rise detection technology by combining smoke sensor and semi-conductor heat sensor in mechanism and circuitry structure. Just because of the combination of smoke detection and heat detection, it not only overcomes the disadvantage that detectors using common infrared scattering technology are insensitive to black smoke with small particles, but also can pick up fire with obvious rise of temperature such as alcohol flame, thus extending its application range.

DI-9102E Intelligent Photoelectric Smoke Detector is a new generation product, connected with intelligent fire alarm control panel to form fire alarm system. The detector turns on fire LED to indicate fire alarm condition and transmits the fire signal to the control panel. The detector is developed from sensing chamber by scattering theory. Besides stable performance and easy maintenance, the detector has the ability to endure dust contamination and environmental light. The detector utilizes drift compensation algorithm: When the environment is changing, such as dust accumulation, humidity and temperature changing, the detector can figure out these drift variation to make up for sensitivity, thus the amount of smoke needed to generate an alarm remains constant, irrespective of environmental conditions.

DI-9406 Addressable Flashing Beacon Base is installed in field to warn people for evacuation with audible and visual alarm in case of a confirmed fire. The flashing beacon base can communicate with fire alarm control panel (FACP) through a built-in microprocessor. On receiving a start command from the FACP, the microprocessor will control the buzzer to generate the pre-set fire alarm sound and light the bright LED.