English
Español
  • Search
    • +34 902930427

    0.00 €

    Analog Intercommunication

    Products 707
    Surface Box for FERMAX® CITY™ Classic S7 Entry Panel [8957]
    Surface Box for FERMAX® CITY™ Classic S7 Entry Panel
    Ref.: 8957
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. In those cases where a hole is not desired or cannot be made in the wall for the embedding box (marble, stone facades, etc.), it is recommended to use a surface box. The depth is only 33mm., And its design integrates perfectly with the aesthetics of the plate. In case of combining several plates, it is not required to use the separator set. Measurements: 130x341x33 mm (horizontal-vertical-depth).
    V.A.T. included
    41.93 €
    Surface Box for FERMAX® CITY™ Classic S6 Entry Panel [8956]
    Surface Box for FERMAX® CITY™ Classic S6 Entry Panel
    Ref.: 8956
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. In those cases where a hole is not desired or cannot be made in the wall for the embedding box (marble, stone facades, etc.), it is recommended to use a surface box. The depth is only 33mm., And its design integrates perfectly with the aesthetics of the plate. In case of combining several plates, it is not required to use the separator set. Measurements: 130x294x33 mm (horizontal-vertical-depth).
    V.A.T. included
    40.73 €
    Surface Box for FERMAX® CITY™ Classic S5 Entry Panel [8955]
    Surface Box for FERMAX® CITY™ Classic S5 Entry Panel
    Ref.: 8955
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. In those cases where a hole is not desired or cannot be made in the wall for the embedding box (marble, stone facades, etc.), it is recommended to use a surface box. The depth is only 33mm., And its design integrates perfectly with the aesthetics of the plate. In case of combining several plates, it is not required to use the separator set. Measurements: 130x246x33 mm (horizontal-vertical-depth).
    V.A.T. included
    38.33 €
    Surface Box for FERMAX® CITY™ Classic S4 Entry Panel [8954]
    Surface Box for FERMAX® CITY™ Classic S4 Entry Panel
    Ref.: 8954
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. In those cases where a hole is not desired or cannot be made in the wall for the embedding box (marble, stone facades, etc.), it is recommended to use a surface box. The depth is only 33mm., And its design integrates perfectly with the aesthetics of the plate. In case of combining several plates, it is not required to use the separator set. Measurements: 130x199x33 mm (horizontal-vertical-depth).
    V.A.T. included
    35.94 €
    Surface Box for FERMAX® CITY™ Classic S3 Entry Panel [8953]
    Surface Box for FERMAX® CITY™ Classic S3 Entry Panel
    Ref.: 8953
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. In those cases where a hole is not desired or cannot be made in the wall for the embedding box (marble, stone facades, etc.), it is recommended to use a surface box. The depth is only 33mm., And its design integrates perfectly with the aesthetics of the plate. In case of combining several plates, it is not required to use the separator set. Measurements: 130x175x33 mm (horizontal-vertical-depth).
    V.A.T. included
    33.54 €
    Surface Box for FERMAX® CITY™ Classic S2 Entry Panel [8952]
    Surface Box for FERMAX® CITY™ Classic S2 Entry Panel
    Ref.: 8952
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. In those cases where a hole is not desired or cannot be made in the wall for the embedding box (marble, stone facades, etc.), it is recommended to use a surface box. The depth is only 33mm., And its design integrates perfectly with the aesthetics of the plate. In case of combining several plates, it is not required to use the separator set. Measurements: 130x151x33 mm (horizontal-vertical-depth).
    V.A.T. included
    31.15 €
    Surface Box for FERMAX® CITY™ Classic S1 Entry Panel [8951]
    Surface Box for FERMAX® CITY™ Classic S1 Entry Panel
    Ref.: 8951
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. In those cases where a hole is not desired or cannot be made in the wall for the embedding box (marble, stone facades, etc.), it is recommended to use a surface box. The depth is only 33mm., And its design integrates perfectly with the aesthetics of the plate. In case of combining several plates, it is not required to use the separator set. Measurements: 130x128x33 mm (horizontal-vertical-depth).
    V.A.T. included
    29.95 €
    FERMAX® CITY™ S4 Kit Embedding Box [8949]
    FERMAX® CITY™ S4 Kit Embedding Box
    Ref.: 8949
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    Consult
    FERMAX® CITY™ S1 Kit Embedding Box [ 8948]
    FERMAX® CITY™ S1 Kit Embedding Box
    Ref.: 8948
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    Consult
    FERMAX® CITY™ S8 Type Flush Mount Box [8858]
    FERMAX® CITY™ S8 Type Flush Mount Box
    Ref.: 8858
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    43.12 €
    FERMAX® CITY™ S7 Type Flush Mount Box [8857]
    FERMAX® CITY™ S7 Type Flush Mount Box
    Ref.: 8857
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    41.93 €
    FERMAX® CITY™ S6 Type Flush Mount Box [8856]
    FERMAX® CITY™ S6 Type Flush Mount Box
    Ref.: 8856
    Para realizar la instalación de una placa es necesario colocar una caja en la pared o muro donde posteriormente fijaremos la placa. Las cajas de empotrar están fabricadas en aluminio y zamak. Disponen de unas bisagras abatibles en cualquier sentido, que permiten sujetar la placa mientras se realiza el cableado. Tienen unas marcas circulares hendidas en el fondo de la caja, que se agujerean con un ligero golpe o presión, permitiendo así el paso de los cables. En el caso que se combinen varias placas, siempre de la misma serie, es necesario la utilización de un juego de separadores para un perfecto acoplamiento. Se requiere un juego por cada placa adicional que se instala entre las cajas de empotrar.
    V.A.T. included
    40.73 €
    FERMAX® CITY™ S5 Type Flush Mount Box [8855]
    FERMAX® CITY™ S5 Type Flush Mount Box
    Ref.: 8855
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    38.33 €
    FERMAX® CITY™ S4 Type Flush Mount Box [8854]
    FERMAX® CITY™ S4 Type Flush Mount Box
    Ref.: 8854
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    35.94 €
    FERMAX® CITY™ S3 Type Flush Mount Box [8853]
    FERMAX® CITY™ S3 Type Flush Mount Box
    Ref.: 8853
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    31.15 €
    FERMAX® CITY™ S2 Type Flush Mount Box [8852]
    FERMAX® CITY™ S2 Type Flush Mount Box
    Ref.: 8852
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    29.95 €
    FERMAX® CITY™ S1 Type Flush Mount Box [8851]
    FERMAX® CITY™ S1 Type Flush Mount Box
    Ref.: 8851
    To carry out the installation of a plate it is necessary to place a box on the wall or wall where we will later fix the plate. The embedding boxes are made of aluminum and zamak. They have hinges that can be folded in any direction, which allow the plate to be held while wiring. They have circular indentations in the bottom of the box, which are punctured with a light tap or pressure, thus allowing the cables to pass through. In the event that several plates are combined, always from the same series, it is necessary to use a set of spacers for a perfect coupling. One set is required for each additional plate that is installed between the flush mounting boxes.
    V.A.T. included
    28.75 €
    Angular Plug for FERMAX® CITY™ Double S7 [8395]
    Angular Plug for FERMAX® CITY™ Double S7
    Ref.: 8395
    Necessary when the plate must be installed in a point of difficult accessibility, for example, behind a fence. It is also useful to be able to focus the camera better, in places where the plate is installed so that the person who has called is out of the field of view of the same. It is made of 2mm thick anodized aluminum. Measurements: 285x345 mm (width-height).
    V.A.T. included
    319.84 €
    Angular Plug for FERMAX® CITY™ Double S6 [8394]
    Angular Plug for FERMAX® CITY™ Double S6
    Ref.: 8394
    Necessary when the plate must be installed in a point of difficult accessibility, for example, behind a fence. It is also useful to be able to focus the camera better, in places where the plate is installed so that the person who has called is out of the field of view of the same. It is made of 2mm thick anodized aluminum. Measurements: 285x300 mm (width-height).
    V.A.T. included
    294.68 €
    Angular Plug for FERMAX® CITY™ Double S5 [8393]
    Angular Plug for FERMAX® CITY™ Double S5
    Ref.: 8393
    Necessary when the plate must be installed in a point of difficult accessibility, for example, behind a fence. It is also useful to be able to focus the camera better, in places where the plate is installed so that the person who has called is out of the field of view of the same. It is made of 2mm thick anodized aluminum. Measurements: 285x250 mm (width-height).
    V.A.T. included
    294.68 €
    FERMAX® CITY™ Classic 8 VP 212 Hollow Entry Panel with Keypad (4+N) - 24 Pushbuttons [8761]
    FERMAX® CITY™ Classic 8 VP 212 Hollow Entry Panel with Keypad (4+N) - 24 Pushbuttons
    Ref.: 8761
    The design of the plate stands out for its curved-convex profile. An included cellular rubber sealing gasket ensures a perfect fit of the plate to the wall, to avoid water leaks. It is possible to combine two or more plates, provided they are from the same series. To fit them perfectly, a set of spacers should be used every two plates that are installed between their embedding boxes. Aluminum color. Call buttons: metallic and rounded in line with the curved profile of the plate. Wiring: 4 common wires + N (1 call wire per home). 12 VAC supply. IPK-437.
    V.A.T. included
    Consult
    FERMAX® CITY™ Classic 8 VP 211 Hollow Entry Panel with Keypad (4+N) - 22 Pushbuttons [8760]
    FERMAX® CITY™ Classic 8 VP 211 Hollow Entry Panel with Keypad (4+N) - 22 Pushbuttons
    Ref.: 8760
    The design of the plate stands out for its curved-convex profile. An included cellular rubber sealing gasket ensures a perfect fit of the plate to the wall, to avoid water leaks. It is possible to combine two or more plates, provided they are from the same series. To fit them perfectly, a set of spacers should be used every two plates that are installed between their embedding boxes. Aluminum color. Call buttons: metallic and rounded in line with the curved profile of the plate. Wiring: 4 common wires + N (1 call wire per home). 12 VAC supply. IPK-437.
    V.A.T. included
    Consult
    FERMAX® CITY™ Classic 8 P 215 Keypad Entry Panel (4+N) - 30 Push Buttons [8748]
    FERMAX® CITY™ Classic 8 P 215 Keypad Entry Panel (4+N) - 30 Push Buttons
    Ref.: 8748
    The design of the plate stands out for its curved-convex profile. An included cellular rubber sealing gasket ensures a perfect fit of the plate to the wall, to avoid water leaks. It is possible to combine two or more plates, provided they are from the same series. To fit them perfectly, a set of spacers should be used every two plates that are installed between their embedding boxes. Aluminum color. Call buttons: metallic and rounded in line with the curved profile of the plate. Wiring: 4 common wires + N (1 call wire per home). 12 VAC supply. IPK-437.
    V.A.T. included
    Consult
    FERMAX® CITY™ Classic 8 P 214 Keypad Entry Panel (4+N) - 28 Pushbuttons [8747]
    FERMAX® CITY™ Classic 8 P 214 Keypad Entry Panel (4+N) - 28 Pushbuttons
    Ref.: 8747
    The design of the plate stands out for its curved-convex profile. An included cellular rubber sealing gasket ensures a perfect fit of the plate to the wall, to avoid water leaks. It is possible to combine two or more plates, provided they are from the same series. To fit them perfectly, a set of spacers should be used every two plates that are installed between their embedding boxes. Aluminum color. Call buttons: metallic and rounded in line with the curved profile of the plate. Wiring: 4 common wires + N (1 call wire per home). 12 VAC supply. IPK-437.
    V.A.T. included
    Consult
    SYSAWAY© 2024 All rights reserved