DF801 is used to connect, terminate, and splice FlexZone loose coaxial cable.

The splice kit (DF800) is used to quickly join or terminate cables and provides a waterproof seal.

DF215 is the sensor cable which can be installed with FlexZone processors. It detects vibrations caused by climbing, cutting, lifting, or disturbing the fence fabric.

Ethernet card, 10/100BASE-TX on RJ45, PoE, G2 Silver.

The DF862 gate disconnect assembly protects gates that are infrequently used. The gate can be opened and closed by manually separating the connection. When the assembly is opened, a supervision alarm is generated. When the assembly is closed the gate is protected and secure.

Single-mode fiber optic (SMFO) comm card for fence protection network option.

The Multi-mode fiber optic (MMFO) comm card is used for multimode fiber optic communications and enables network option for FlexPS processor.

The FlexZone processor (DF104) gives advanced warning of unwanted intrusions at the perimeter and is easily installed on most fences by attaching its lightweight sensor cable to the fence fabric with cable ties. The DF104 processor provides up to 4 independent zones of detection and comes in an outdoor rated enclosure, which can be easily post mounted or fixed to any convenient supporting surface.

Receiving card for door sensor via radio. Battery or solar power. No physical connection to auxiliary device

EIA-422 network interface card for copper wire communications enables network option for FlexPS processor.

The FlexZone™ wireless door sensor consists of two main components: the sensor module and the receiver card installed inside the FlexZone™ processor. The sensor module analyzes vibration, movement and position data. Transmits intrusion, monitoring devices, power levels, status of the RF link and status of entries to the receiving card through an encrypted wireless link

The FlexZone™ wireless door sensor consists of two main components: the sensor module and the receiver card installed inside the FlexZone™ processor. The sensor module analyzes vibration, movement and position data. It transmits intrusion, monitoring devices, power levels, status of the RF link and status of inputs to the receiving card through an encrypted wireless link.

FlexZone processor (DF160) gives advanced warning of unwanted intrusions at the perimeter and is easily installed on most fences by attaching its lightweight sensor cable to the fence fabric with cable ties. The DF160 processor provides up to 60 independent zones of detection and comes in an outdoor rated enclosure, which can be easily post mounted or fixed to any convenient supporting surface.

AC-DC power supply for mounting on DIN rail TS-35 / 7.5 or 15, single output. Output voltage from 48 VDC to 0.83 Amp. With LED power indicator and overload protection, short-circuit and overvoltage. Passive cooling by air passage. Output power ratio 39.8 W.

UltrakLink™ processor module with 8/8 relay inputs / outputs. DIN rail mounting. Ultralink I / O modules are used to receive and / or transmit alarm information as part of an integrated security system. The application includes: (1) Conversion of FlexZone™ sensor alarms collected from the Silver Network to relays or open collector, for use in inputs of a third party Alarm Management System. (2) Connection of dry contacts of auxiliary alarm sensors to integrate in management systems. The UltraLink™ I / O module connects to the Silver Network through a communication card. It is possible to link up to 8 UltraLink™ expansion modules to an UltraLink™ communication card (DF432). The operating mode of the relay outputs, collector outputs or contact inputs is configured from the UCM software. The UCM software can be connected to the UltraLink™ modules through a direct USB connector from the I / O processor, or via IP through the network management software.

Mini network interface unit (USB to RS-422 and single-mode fiber), DIN rail mounting. The mini SNIU is USB to fiber converter / RS-422 DIN rail mounting for the connection of the wired network to the controller network management system. The mini SNIU facilitates the following interfaces: EIA-422 and fiber optic connections.

Mini network interface unit (USB to RS-422 and Multimode Fiber), DIN rail mounting. The mini SNIU is a USB to fiber converter / RS-422 DIN rail mount for connecting the wired network to the controller network management system. The mini SNIU facilitates the following interfaces: EIA-422 and fiber optic connections.

UltraLink™ link extension cable. Connection cable between modules. Length 23 cm.

UltraLink processor module with 32 relay outputs. DIN rail mounting. The 32 relay output card can be used to extend the UltraLink input and output processor module (DF420). Up to 8 expansion cards can be expanded.

Power 230 VAC / 21 VAC in box for microwave barriers MRW. In box with IP66 protection. Dimensions of 110 x 180 x 90 mm, excluding wiring inputs.

Mounting kit for barrier mounting, power supply or batteries in PB column. (Pack of 2 units).

Anti-climbing protection for 360º barriers.

Anti-climbing protection for 180º barriers.

Cover for 3 meters high column. Tamper output (NC). Includes mounting kit. Working temperature: -15ºC to 50ºC.