High efficiency, cost effective range of Switch Mode power supplies for use in Access Control, CCTV and General Purpose applications. Modular construction provides for easy maintenance and upgrade capability. Boxed and Unboxed Models. Voltage range: 12 V, 3+0,5 A.

High efficiency, cost effective range of Switch Mode power supplies for use in Access Control, CCTV and General Purpose applications. Modular construction provides for easy maintenance and upgrade capability. Boxed and Unboxed Models. Voltage range: 12 V, 2+0,5 A.

High efficiency, cost effective range of Switch Mode power supplies for use in Access Control, CCTV and General Purpose applications. Modular construction provides for easy maintenance and upgrade capability. Boxed and Unboxed Models. Voltage range: 12 V, 1+0,5 A.

The EN range of power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing Intruder Alarm Systems to grade 3 under PD6662:2010 / EN50131, with built in quality and reliability. Comprehensive Battery Management. Deep Discharge Protection. Battery Fault Detection (grade 3). Double Battery Model has independent Battery Charging & Monitoring. Dedicated Fault Outputs. EPS Fault (mains fail). APS Fault (battery fault) (grade 3). PSU Fault (general fault). Internal LED PSU Status. Full Rated Current To Load + Battery Charging. Electronic Overload Protection. Mains Transient Protection. Output (mains on): 13.8V dc nominal. Load Output: 34 Maximum 3.0A 12 hours - 2.8/3.0A. Mains Supply: 230V +10%/-15%@50Hz. Environment: -10C to 40C @ 95%RH. Enclosure Type R: 410 H x 390 W x 90 D (Clam Lid). Box Sizes for battery: "34" models: 2 x 17 or 18Ah 3.0A**. Standards: EN3 - Grade 3 Environmental Class II. **Full current to load plus additional current to charge standby battery.

Metallic box with Grade 3 power supply unit for accessories and expanders of LightSYS™ 2 and ProSYS™ PLUS main panels. Dimensions: 375 x 330 x 98 mm.

Power supply unit in BUS with 12VDC 3A output into an enclosure, with transformer and 2 relays. Certified EN50131 Grade 3. For LightSYS™ and ProSYS™ / ProSYS™ Plus main panels. Supervised with 4-wire BUS connection Incorporating battery charger. Supports battery up to 12V / 21Ah. Full supervision of low battery, loss of network power, loop failure and auxiliary output. Incorporates tamper. The circuit and the transformer are supplied into the box. Built-in sounder output (12 VDC / 1.7 A) and overload protection. Dimensions: 110 x 90 x 30 mm. Maximum panel distance: 300 m. Max consumption on the bus: 180 mA.

Backup power supply designed in accordance with the requirements of EN 50131, grade 1 ÷ 2. It is intended for an uninterrupted supply of alarm system devices that require a stabilized voltage of 12 VDC (+/- 15%). The linear stabilization system, which has been used in the unit, provides voltage with a lower noise level and a faster response to interference compared to a switched mode regulator. Power supply: 230VAC / 50Hz. Power supply output: (1) 3A / 27.6VDC - for general application (2) 1.41A / 27.6VDC - for grade 1, 2. Battery charging current: 0.5A / 1A. Batteries supported: 2 x 7Ah / 2 x 17Ah (12V). Current consumption by PSU systems: 15 mA max. Protections: SCP, OLP, OVP, UVP, sabotage (opening of the enclosure). Technical outputs type OC: EPS - 230V AC power failure, APS - battery failure. Compliance with standards: EN50131, level 1 ÷ 2, EN60839-11. Dimensions: 335 x 385 x 173 [+/- 2mm] (ground clearance: 14mm). Surface mounted box, locked - bolted.

Backup power supply designed in accordance with the requirements of EN 50131, grade 1 ÷ 2. It is intended for an uninterrupted supply of alarm system devices that require a stabilized voltage of 12 VDC (+/- 15%). The linear stabilization system, which has been used in the unit, provides voltage with a lower noise level and a faster response to interference compared to a switched mode regulator. Power supply: 230VAC / 50Hz. Power supply output: (1) 3A / 13.8VDC - for general application (2) 1.41A / 13.8VDC - for grade 1, 2. Battery charging current: 0.5A / 1A. Supported battery: 17Ah / 12V. Current consumption by PSU systems: 15 mA max. Protections: SCP, OLP, OVP, UVP, sabotage (opening of the enclosure). Technical outputs type OC: EPS - 230V AC power failure, APS - battery failure. Compliance with standards: EN50131, level 1 ÷ 2, EN60839-11. Dimensions: 235 x 305 x 82 [+/- 2mm] (ground clearance: 8mm). Surface mounted box, locked - bolted.

Backup power supply designed in accordance with the requirements of EN 50131, grade 1 ÷ 2. It is intended for an uninterrupted supply of alarm system devices that require a stabilized voltage of 12 VDC (+/- 15%). The linear stabilization system, which has been used in the unit, provides voltage with a lower noise level and a faster response to interference compared to a switched mode regulator. Power supply: 230VAC / 50Hz. Power supply output: (1) 2A / 27.6VDC - for general application (2) 0.58A / 27.6VDC - for grade 1, 2. Battery charging current: 0.5A / 1A. Batteries supported: 2 x 7Ah / 12V. Current consumption by PSU systems: 15 mA max. Protections: SCP, OLP, OVP, UVP, sabotage (opening of the enclosure). Technical outputs type OC: EPS - 230V AC power failure, APS - battery failure. Compliance with standards: EN50131, level 1 ÷ 2, EN60839-11. Dimensions: 205 x 305 x 82 [+/- 2mm] (ground clearance: 8mm). Surface mounted box, locked - bolted.

Backup power supply designed in accordance with the requirements of EN 50131, grade 1 ÷ 2. It is intended for an uninterrupted supply of alarm system devices that require a stabilized voltage of 12 VDC (+/- 15%). The linear stabilization system, which has been used in the unit, provides voltage with a lower noise level and a faster response to interference compared to a switched mode regulator. Power supply: 230VAC / 50Hz. Power supply output: (1) 5A / 13.8VDC - for general application (2) 3.33A / 13.8VDC - for grade 1, 2. Battery charging current: 0.5A / 1A / 2A. Supported battery: 1 x 7Ah / 1 x 17Ah / 1 x 40Ah (12V). Current consumption by PSU systems: 15 mA max. Protections: SCP, OLP, OVP, UVP, sabotage (opening of the enclosure). Technical outputs type OC: EPS - 230V AC power failure, APS - battery failure. Compliance with standards: EN50131, level 1 ÷ 2, EN60839-11. Dimensions: 335 x 385 x 173 [+/- 2mm] (ground clearance: 8mm). Surface mounted box, locked - bolted.

Backup power supply designed in accordance with the requirements of EN 50131, grade 1 ÷ 2. It is intended for an uninterrupted supply of alarm system devices that require a stabilized voltage of 12 VDC (+/- 15%). The linear stabilization system, which has been used in the unit, provides voltage with a lower noise level and a faster response to interference compared to a switch mode regulator. Power supply: 230VAC / 50Hz. Power supply output: (1) 5A / 13.8VDC - for general application (2) 1.41A / 13.8VDC - for grade 1, 2. Battery charging current: 0.5A / 1A / 2A. Supported battery: 17Ah / 12V. Current consumption by PSU systems: 15 mA max. Protections: SCP, OLP, OVP, UVP, sabotage (opening of the enclosure). Technical outputs type OC: EPS - 230V AC power failure, APS - battery failure. Compliance with standards: EN50131, level 1 ÷ 2, EN60839-11. Dimensions: 305 x 305 x 105 [+/- 2 mm] (ground clearance: 8 mm). Surface mounted box, locked - bolted.

Backup power supply designed in accordance with the requirements of EN 50131, grade 1 ÷ 2. It is intended for an uninterrupted supply of alarm system devices that require a stabilized voltage of 12 VDC (+/- 15%). The linear stabilization system, which has been used in the unit, provides voltage with a lower noise level and a faster response to interference compared to a switched mode regulator. Power supply: 230VAC / 50Hz. Power supply output: (1) 2A / 13.8VDC - for general application (2) 0.58A / 13.8VDC - for grade 1, 2. Battery charging current: 0.2A / 0.5A. Supported battery: 7Ah / 12V. Current consumption by PSU systems: 15 mA max. Protections: SCP, OLP, OVP, UVP, sabotage (opening of the enclosure). Technical outputs type OC: EPS - 230V AC power failure, APS - battery failure. Compliance with standards: EN50131, level 1 ÷ 2, EN60839-11. Dimensions: 205 x 237 x 82 [+/- 2mm] (ground clearance: 8mm). Surface mounted box, locked - bolted.

Switch mode buffer power supply unit (with a transformer) PSBEN/LED series. Dimensions: 405 x 375 x 178 mm. Uin=230VAC/50Hz, Uout=5,41A/13,8VDC - for grade 1,2; 2,16A/13,8VDC - for grade 3; 10A/13,8VDC - for general application, tamper: 2xNC, 65Ah. Anti-sabotage protection, space for battery 12V SLA, UVP (battery protection). Technical outputs: EPS (AC failure), PSU (power supply failure) and APS (battery failure). EN50131 Grade 1, 2 and 3 compliant.

Switch mode buffer power supply unit (with a transformer) PSBEN/LCD series. Dimensions: 405 x 355 x 98 [mm], Uin=230VAC/50Hz, Uout=5A/27,6VDC, tamper: 2xNC, 2x17Ah. Anti-sabotage protection, space for battery 12V SLA, UVP (battery protection). Technical outputs: EPS (AC failure), PSU (power supply failure), APS (battery failure). EN50131 Grade 1, 2 and 3 compliant.

Switch mode buffer power supply unit (with a transformer) PSBEN/LCD series. Dimensions: 405 x 375 x 178 [mm], Uin=230VAC/50Hz, Uout=5,41A/13,8VDC - for grade 1,2; 2,16A/13,8VDC - for grade 3; 10A/13,8VDC - for general application, tamper: 2xNC, 65Ah. Anti-sabotage protection, space for battery 12V SLA, UVP (battery protection). Technical outputs: EPS (AC failure), PSU (power supply failure), APS (battery failure). EN50131 Grade 1, 2 and 3 compliant.

Switch mode buffer power supply unit (with a transformer) PSBEN/LCD series. Dimensions: 335 x 355 x 178 [mm], Uin=230VAC/50Hz, Uout=2,8A/13,8VDC - for grade 1,2; 1,33A/13,8VDC - for grade 3; 5A/13,8VDC - for general application, tamper: 2xNC, 40Ah. Anti-sabotage protection, space for battery 12V SLA, UVP (battery protection). Technical outputs: EPS (AC failure), PSU (power supply failure), APS (battery failure). EN50131 Grade 1, 2 and 3 compliant.

Switch mode buffer power supply unit (with a transformer) PSBEN/LED series. Dimensions: 405 x 355 x 98 [mm], Uin=230VAC/50Hz, Uout=5A/27,6VDC, tamper: 2xNC, 2x17Ah. Anti-sabotage protection, space for battery 12V SLA, UVP (battery protection). Technical outputs: EPS (AC failure), PSU (power supply failure), APS (battery failure). EN50131 Grade 1, 2 and 3 compliant.

Switch mode buffer power supply unit (with a transformer) PSBEN/LED series. Dimensions: 335 x 355 x 178 mm. Uin=230VAC/50Hz, Uout=2,8A/13,8VDC - for grade 1,2; 1,33A/13,8VDC - for grade 3; 5A/13,8VDC - for general application, tamper: 2xNC, 40Ah. Anti-sabotage protection, space for battery 12V SLA, UVP (battery protection). Technical outputs: EPS (AC failure), PSU (power supply failure) and APS (battery failure). EN50131 Grade 1, 2 and 3 compliant.

Switch mode buffer power supply unit (with a transformer) PSBEN/LED series. Dimensions: 335 x 355 x 108 mm. Uin=230VAC/50Hz, Uout=1,4A/13,8VDC - for grade 1,2; 0,56A/13,8VDC - for grade 3; 5A/13,8VDC - for general application, tamper: 2xNC, 17Ah. Anti-sabotage protection, space for battery 12V SLA, UVP (battery protection). Technical outputs: EPS (AC failure), PSU (power supply failure) and APS (battery failure). EN50131 Grade 1, 2 and 3 compliant.

Switch mode buffer power supply unit (with a transformer) PSBEN/LED series. Dimensions: 305 x 305 x 98 mm. Uin=230VAC/50Hz, Uout=1,4A/13,8VDC - for grade 1,2; 0,56A/13,8VDC - for grade 3; 3A/13,8VDC - for general application, tamper: 2xNC, 17Ah. Anti-sabotage protection, space for battery 12V SLA, UVP (battery protection). Technical outputs: EPS (AC failure), PSU (power supply failure) and APS (battery failure). EN50131 Grade 1, 2 and 3 compliant.

Switched power supply - module 13.8 VDC / max. 10.0A total, without trouble outputs and disconection of discharged battery, WAGO connector, size 238 x 55 x 120 mm (W x H x D), protection IP 20.

This product is intended for general use to feed electric and electronic devices in covered rooms, in environments without risk of explosion. Suitable to place inside cameras of security systems. Mounting with self-adhesive tape. Stabilized output voltage. Voltage 12 VDC - 1.4 Amp. Input - twin-lead power wire with double insulation. Output - twin-lead wire. Protection degree IP20.

Switched power supply - module 13.8 VDC / max. 5.0A total, with separate accumulator clamps, without trouble outputs and disconection of discharged battery. Size 119 x 102 x 45 mm (W x H x D). Protection IP 20. DIN rail mounting.

The switched power supply - module 13.8 VDC / max. 10.0A total, without trouble outputs, with disconection of discharged battery, WAGO connector, size 238 x 55 x 120 mm (W x H x D), protection IP 20.