Wall or roof mounting bracket for EV100, EV1000, VE1000 y DD1000 series of detectors. Allows to add a wall tamper (ST400 accessory not included).

Placa de montaje de detectores sísmicos UTC™ para facilitar su instalación sobre hormigón. Dimensiones: 80 x 97 x 5 mm.

UTC™ Adhesive Kit For Glass Break Detector: glue and cleaning towels

Flush mounting accessory for EV669 y DD669 series.

UTC™ Adhesive Kit For Laminated Glass Break Detector Laminado: glue and cleaning towels

Network interface that converts the physical media of the FlexZone network into a standard computer interface (USB, ETHERNET, EIA-232). Allows FlexZone processors to communicate alarm, status and configuration information. The input power for the DF955-U is 12 to 48VDC, the consumption is 3W. PSU-3.5A compatible power supply or if you have the DF648 you can also use it.

UV-resistant nylon tie wraps are used to secure the cable to the fence fabric. For standard chain link fencing cable ties are fastened to the fence and cable at 25 to 30 cm intervals. Please refer to the manual for other types of fences or for information on varying cable tie spacing. A single bag of UV-resistant tie wraps is sufficient for installing one entire 150 m of sensor cable.

DF801 is used to connect, terminate, and splice FlexZone loose coaxial cable.

The splice kit (DF800) is used to quickly join or terminate cables and provides a waterproof seal.

DF215 is the sensor cable which can be installed with FlexZone processors. It detects vibrations caused by climbing, cutting, lifting, or disturbing the fence fabric.

Ethernet card, 10/100BASE-TX on RJ45, PoE, G2 Silver.

The DF862 gate disconnect assembly protects gates that are infrequently used. The gate can be opened and closed by manually separating the connection. When the assembly is opened, a supervision alarm is generated. When the assembly is closed the gate is protected and secure.

Single-mode fiber optic (SMFO) comm card for fence protection network option.

The Multi-mode fiber optic (MMFO) comm card is used for multimode fiber optic communications and enables network option for FlexPS processor.

The FlexZone processor (DF104) gives advanced warning of unwanted intrusions at the perimeter and is easily installed on most fences by attaching its lightweight sensor cable to the fence fabric with cable ties. The DF104 processor provides up to 4 independent zones of detection and comes in an outdoor rated enclosure, which can be easily post mounted or fixed to any convenient supporting surface.

Receiving card for door sensor via radio. Battery or solar power. No physical connection to auxiliary device

EIA-422 network interface card for copper wire communications enables network option for FlexPS processor.

The FlexZone™ wireless door sensor consists of two main components: the sensor module and the receiver card installed inside the FlexZone™ processor. The sensor module analyzes vibration, movement and position data. Transmits intrusion, monitoring devices, power levels, status of the RF link and status of entries to the receiving card through an encrypted wireless link

The FlexZone™ wireless door sensor consists of two main components: the sensor module and the receiver card installed inside the FlexZone™ processor. The sensor module analyzes vibration, movement and position data. It transmits intrusion, monitoring devices, power levels, status of the RF link and status of inputs to the receiving card through an encrypted wireless link.

FlexZone processor (DF160) gives advanced warning of unwanted intrusions at the perimeter and is easily installed on most fences by attaching its lightweight sensor cable to the fence fabric with cable ties. The DF160 processor provides up to 60 independent zones of detection and comes in an outdoor rated enclosure, which can be easily post mounted or fixed to any convenient supporting surface.

AC-DC power supply for mounting on DIN rail TS-35 / 7.5 or 15, single output. Output voltage from 48 VDC to 0.83 Amp. With LED power indicator and overload protection, short-circuit and overvoltage. Passive cooling by air passage. Output power ratio 39.8 W.

UltrakLink™ processor module with 8/8 relay inputs / outputs. DIN rail mounting. Ultralink I / O modules are used to receive and / or transmit alarm information as part of an integrated security system. The application includes: (1) Conversion of FlexZone™ sensor alarms collected from the Silver Network to relays or open collector, for use in inputs of a third party Alarm Management System. (2) Connection of dry contacts of auxiliary alarm sensors to integrate in management systems. The UltraLink™ I / O module connects to the Silver Network through a communication card. It is possible to link up to 8 UltraLink™ expansion modules to an UltraLink™ communication card (DF432). The operating mode of the relay outputs, collector outputs or contact inputs is configured from the UCM software. The UCM software can be connected to the UltraLink™ modules through a direct USB connector from the I / O processor, or via IP through the network management software.

Mini network interface unit (USB to RS-422 and single-mode fiber), DIN rail mounting. The mini SNIU is USB to fiber converter / RS-422 DIN rail mounting for the connection of the wired network to the controller network management system. The mini SNIU facilitates the following interfaces: EIA-422 and fiber optic connections.

Mini network interface unit (USB to RS-422 and Multimode Fiber), DIN rail mounting. The mini SNIU is a USB to fiber converter / RS-422 DIN rail mount for connecting the wired network to the controller network management system. The mini SNIU facilitates the following interfaces: EIA-422 and fiber optic connections.