The GEN Switch Mode range of power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing Intruder Alarm Systems to grade 2 and 3 under PD6662:2010 / EN50131-6:2008, with built in quality and reliability. Both grades of product are available in two power variants with a range of enclosure sizes providing the required space for the standby battery. Two LED’s assist with quick and easy installation by showing presence of mains, correct battery charging or a fault condition, whilst fault outputs are available to relay this information back to the intruder panel. Each PSU incorporates intelligent battery management comprising of full load battery testing, low battery voltage detection and deep discharge protection. PSU protection is builit-in as standard including mains transient filtering, electronic output overload protection and fuses on the load and battery outputs. Voltage range: 12 V, 1+0,6 A. GRADE 3.

The GEN Switch Mode range of power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing Intruder Alarm Systems to grade 2 and 3 under PD6662:2010 / EN50131-6:2008, with built in quality and reliability. Both grades of product are available in two power variants with a range of enclosure sizes providing the required space for the standby battery. Two LED’s assist with quick and easy installation by showing presence of mains, correct battery charging or a fault condition, whilst fault outputs are available to relay this information back to the intruder panel. Each PSU incorporates intelligent battery management comprising of full load battery testing, low battery voltage detection and deep discharge protection. PSU protection is builit-in as standard including mains transient filtering, electronic output overload protection and fuses on the load and battery outputs. Voltage range: 12 V, 1,5+0,8 A. GRADE 2.

High efficiency, cost effective range of Switch Mode power supplies for use in Access Control, CCTV and General Purpose applications. Modular construction provides for easy maintenance and upgrade capability. Boxed and Unboxed Models. Voltage range: 12 V, 5+1 A.

Switching power supply 12 V, 5 + 0.5 Amp. High efficiency power supply for use in access control applications, CCTV, intrusion and general purpose applications. Its modular construction allows easy maintenance and updating capacity. Model in box.

High efficiency, cost effective range of Switch Mode power supplies for use in Access Control, CCTV and General Purpose applications. Modular construction provides for easy maintenance and upgrade capability. Boxed and Unboxed Models. Voltage range: 12 V, 4+1 A.

High efficiency, cost effective range of Switch Mode power supplies for use in Access Control, CCTV and General Purpose applications. Modular construction provides for easy maintenance and upgrade capability. Boxed and Unboxed Models. Voltage range: 12 V, 3+0,5 A.

High efficiency, cost effective range of Switch Mode power supplies for use in Access Control, CCTV and General Purpose applications. Modular construction provides for easy maintenance and upgrade capability. Boxed and Unboxed Models. Voltage range: 12 V, 2+0,5 A.

High efficiency, cost effective range of Switch Mode power supplies for use in Access Control, CCTV and General Purpose applications. Modular construction provides for easy maintenance and upgrade capability. Boxed and Unboxed Models. Voltage range: 12 V, 1+0,5 A.

The EN range of power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing Intruder Alarm Systems to grade 3 under PD6662:2010 / EN50131, with built in quality and reliability. Comprehensive Battery Management. Deep Discharge Protection. Battery Fault Detection (grade 3). Double Battery Model has independent Battery Charging & Monitoring. Dedicated Fault Outputs. EPS Fault (mains fail). APS Fault (battery fault) (grade 3). PSU Fault (general fault). Internal LED PSU Status. Full Rated Current To Load + Battery Charging. Electronic Overload Protection. Mains Transient Protection. Output (mains on): 13.8V dc nominal. Load Output: 34 Maximum 3.0A 12 hours - 2.8/3.0A. Mains Supply: 230V +10%/-15%@50Hz. Environment: -10C to 40C @ 95%RH. Enclosure Type R: 410 H x 390 W x 90 D (Clam Lid). Box Sizes for battery: "34" models: 2 x 17 or 18Ah 3.0A**. Standards: EN3 - Grade 3 Environmental Class II. **Full current to load plus additional current to charge standby battery.

Power distribution module for IP cameras (PoE). Size: 75 x 73 x 33 mm, Uin=20÷56 VDC (+/-2%), UPoE=Uin (equal to supply voltage), 4x1.0A. Number of power inputs: 2 - DC 5.5/2.1 socket or screw terminal – max. cable length 1.5mm2. Number of PoE outputs: 4 – RJ45. The module supports both 10Mbps and 100Mbps networks.

Stabilized DC power supply is intended for supply any LAN devices through Ethernet Cable, which require stabilized voltage of 48V DC. The unit provide power through 4/5pins(+) and 7/8pins(-) in Ethernet cable that according to the Ethernet standard are not used to transmit data (data communication is made using pairs: 1/2 and 3/6). The Power supply can't be used in Gigabit Ethernet! The unit is protected against short-circuit and overload. Desktop type power supply unit. Size: 119 x 61 x 38 mm. Input: 90÷264VAC. Output: 0.5A/48VDC – RJ45, designed for 10Mbit/s and 100Mbit/s.

PoE buffer power supply unit for IP cameras. Size: 300 x 407 x 126 mm. Uin=176÷264VAC, Uout=54VDC. ?I=4x0.25A + 0.3A battery charging. Tamper: 1xNC, 4x7Ah-UVP, OLP, OVP, SCP with standard fuses or PTC fuses, FPS – (indication of output fuse activation) - OC type and relay type.

Switch mode buffer power supply unit for HD cameras 13,8VDC and recorder 12VDC, and recorder space + transmitters. Size: 425 x 540 x 190+14 mm. ?I=11A, 16x0.8A/13.8VDC + 1x5A/12VDC (RJ45 + JACK5.5/2.1). Set includes P-TRPV120 transmitters for up to 12 cameras (Recorder space: 380 x 335 x 80 mm). Tamper: 1xNC, 17Ah-UVP (battery protection).

Switch mode buffer power supply unit (transformerless) for cameras 12VDC (+/- 15%). Size: 285 x 297 x 80+8 mm. Uin=176÷264VAC, Uout=13,8VDC/5x1A. ?I=5A+2A. Tamper: 1xNC, 17Ah. SCP (short-circuit protection) with standard fuses, OVP (over voltage protection), OLP (overload protection), UVP (deep discharge battery protection).

Power supply for cameras 12VDC with independent control of each output channel. Size: 205 x 220 x 50+8 mm. Uin=85÷264VAC, Uout=12,0÷15VDC. 4 x adjustment. 4x1A (independent regulation and galvanic separation of each channel). OVP (over voltage protection), SCP (short-circuit protection) with standard fuses.

Power supply for 12VDC cameras, for long lines with galvanic separation of each channel dedicated to DCDC-H inverters. Size: 270 x 154 x 80+8 mm. Uout=30V÷35VDC (100% load ÷ 0% load). 4x1A@30V DC max. SCP (short-circuit protection): 4x T 1A with standard fuses. Power supply - intended to the DCDC10H and DCDC15H converters).

Power supply for 12VDC cameras , two-section. Size: 300 x 301 x 52+8 mm. Uin=176÷264VAC, Uout=12÷15VDC. 2 x adjustment, 16x0.87A, 14A. SCP (short-circuit protection) with standard fuses, OVP (over voltage protection).

Power supply for 12VDC cameras , two-section. Size: 300 x 301 x 52+8 mm. Uin=176÷264VAC, Uout=12÷15VDC. 2 x adjustment, 8x1A, 8A. SCP (short-circuit protection) with standard fuses, OVP (over voltage protection).

Power supply for 12VDC cameras. Switch mode (without a transformer), in metal casing. Size: 235 x 235 x 58 mm. Uin=85÷264VAC, Uout=12.0÷15.0VDC. 1 x adjustment, 8x0.5A , 4A. AW (failure output), OVP (over voltage protection), SCP (short-circuit protection) with standard fuses or PTC fuses, LED 1x8: DC, LED 1x1: AW.

Camera AC Adapter (type A,G,C Universal) 12V 2A (for CC01, CZ01 CD01).

Camera AC Adapter (type A USA) 12V 2A (for CC01, CZ01 CD01).

24 VDC / 3.5 Amp power supply for access control.

220/18 Vca - 45 VA Transformer.

Relay module of the PSBS technical outputs. 66.5 x 39.5 x 18 mm, intended to PSBS series. Output: 13.8 / 27.6VDC (Blue Power).