The step down converter DC/DC 3Amp (DC/DC30HV) is used for step down the input voltage from the range between 28V÷60VDC to the voltage range of 12V÷24VDC at the output, adjusted with a potentiometer. The maximum load current is Imax=3Amp (Pmax=36W). Input voltage: 28V÷60VDC. Voltage adjustment range: 12÷24VDC. Output current: 3Amp/12VDC. Protections: OLP, SCP. Technical outputs: PSU – converter failure. Dimensions: L=130 W=43 H=45 mm. Installation: a mounting panel with an adhesive tape, mounting screws.

The DC/DC 5Amp (DC/DC50SD-SEP) buck converter is used to reduce the voltage from 20V ÷ 28V DC at the converter input to 12VDC at the output. The maximum load current is Imax=5Amp (PMAX= 60W). The module is galvanically isolated between the input and output (IN-AUX). Input voltage: 20V÷28VDC. Output voltage: 12VDC / Galvanic isolation: input - output. Output current: 5Amp/12VDC. Protections: OLP, SCP, OVP. Dimensions: L=150 W=54 H=60 [+/- 2mm]. Installation: a mounting panel with an adhesive tape, mounting screws.

The DC/DC 5Amp (DC/DC50SE) voltage-step up / step down converter is used for maintaining a constant output voltage in the range between 5÷15VDC, adjusted with the VADJ potentiometer, regardless of the input voltage fluctuations in the range of 9.5V ÷ 16VDC. When the input voltage at the output is lower than needed, the converter increases it to the set value. When the input voltage at the output is higher than needed, the converter lowers it to the needed value set by the VADJ potentiometer. The maximum load current is Imax=5Amp (Pmax = 60W). Input voltage: 9.5V÷16VDC. Voltage adjustment range: 5÷15VDC. Output current: 5Amp / 12VDC. Protections: Overload protection, Short-circuit protection. Technical outputs: PSU – converter failure. Dimensions: L=150 W=50 H=60 mm. Installation: a mounting panel with an adhesive tape, mounting screws.

The DC/DC 2Amp (DC/DC20SE) voltage-step up / step down converter is used for maintaining a constant output voltage in the range between 5÷15VDC, adjusted with the VADJ potentiometer, regardless of the input voltage fluctuations in the range of 9.5V ÷ 16VDC. When the input voltage at the output is lower than needed, the converter increases it to the set value. When the input voltage at the output is higher than needed, the converter lowers it to the needed value set by the VADJ potentiometer. The maximum load current is Imax=2Amp (Pmax = 24W). Input voltage: 9.5V÷16VDC. Voltage adjustment range: 5÷15VDC. Output current: 2Amp / 12VDC. Protections: Overload protection, Short-circuit protection. Technical outputs: PSU – converter failure. Dimensions: L=110 W=43 H=27 mm. Installation: a mounting panel with an adhesive tape, mounting screws.

The step down converter DC/DC 2Amp (DC/DC20SD) is used for step down the input voltage from the range between 8V÷28VDC to the voltage range of 4.5V÷19VDC at the output, adjusted with a potentiometer. The maximum load current is Imax=2Amp (Pmax=24W). Input voltage: 8V÷28VDC. Voltage adjustment range: 4.5÷19VDC. Output current: 2Amp / 12VDC. Protections: Short-circuit protection, Overload protection, overheating protection. Technical outputs: PSU – converter failure. Dimensions: L=100 W=43 H=27 mm. Installation: a mounting panel with an adhesive tape, mounting screws. Notes: The minimum difference between the input voltage and the output voltage is: 3V.

The step down converter DC/DC 5Amp (DC/DC50HV) is used for step down the input voltage from the range between 28V÷60VDC to the voltage range of 12V÷24VDC at the output, adjusted with a potentiometer. The maximum load current is Imax=5Amp (Pmax=60W). Input voltage: 28V÷60VDC. Voltage adjustment range: 12÷24VDC. Output current: 5Amp/12VDC. Protections: OLP, SCP. Technical outputs: PSU – converter failure. Dimensions: L=140 W=43 H=45 mm. Installation: a mounting panel with an adhesive tape, mounting screws.

The step down converter DC/DC 1Amp (DC/DC10SD) is used for step down the input voltage from the range between 8V÷28VDC to the voltage range of 4.5V÷19VDC at the output, adjusted with a potentiometer. The maximum load current is Imax=1Amp (Pmax=12W). Input voltage: 8V÷28VDC. Voltage adjustment range: 4.5÷19VDC. Output current: 1Amp / 12VDC. Protections: Short-circuit protection, Overload protection, overheating protection. Technical outputs: PSU – converter failure. Dimensions: L=80 W=43 H=27 mm. Installation: a mounting panel with an adhesive tape, mounting screws. Notes: The minimum difference between the input voltage and the output voltage is: 3V.

The step down converter DC/DC 5Amp (DC/DC50SD) is used for step down the input voltage from the range between 8V÷28VDC to the voltage range of 4.5V÷24VDC at the output, adjusted with a potentiometer. The maximum load current is Imax=5Amp (Pmax=60W). Input voltage: 8V÷28VDC. Voltage adjustment range: 4.5÷24VDC. Output current: 5Amp / 12VDC. Protections: Short-circuit protection, Overload protection, overheating protection. Technical outputs: PSU – converter failure. Dimensions: L=140 W=43 H=45 mm. Installation: a mounting panel with an adhesive tape, mounting screws. Notes: The minimum difference between the input voltage and the output voltage is: 3V.

The over voltage protection module is intended for protecting systems powered with 12V DC against being supplied with too high supply power (e.g. as a result of damaged stabilising system of a PSU). When the maximum accessible input voltage is detected, the output is cut off protecting the receivers from damaging. Activation of the system is indicated by the red LED – L1. Protections against overvoltage OVP. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws or integrated adhesive tape. voltage: 9V-40V DC. Output voltage: 9V ÷ 14,1V DC (+/-0,4V). Output disconnection voltage: 14,1V (+/-0,4V). Load current 4A max. LED indication. Operating temperature: -10°C..50°C. Dimensions: 50 x 43 x 26 mm.

Fuse module, a power distribution module. The LB4P/4x1.5A/FTA fuse module is designed for power distribution in low-voltage systems requiring voltage of 10V÷30V DC or 10V÷24V AC (e.g. buffer power supply, transformer etc.). It has 4 independent, galvanically isolated power supply circuits protected with 1,5A fuses. Fuse activation is indicated by switching off the appropriate LED: L1 for AUX1, L2 for AUX2 etc. Additionally, each output is protected with a varistor protecting the power supply and receivers against surges in the supply system. The module is adapted for connection of wires with a maximum cross-section of 1mm². Protections against: a short circut SCP, an overload OLP, a surge. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. Supply voltage range: 10-30VDC / 10-24VAC. Output voltage: Uaux = Uin ( equal to supply voltage ). Power consumption: 5mA - 30mA. Power inputs: 4 (IN terminals) – max. 1mm² cable. Number of outputs: 4 (AUX terminals) – max. 1mm² cable. Fuse: 4x1.5Amp – TOPIK. Operating temperature: -10°C..50°C. Dimensions: 100 x 43 x 20 mm.

Fuse module, a power distribution module. The module enables the power supply section 8 independent channels. Short circuit, sabotage or other attempt to damage the terminal does not affect the operation of other devices connected to the same power source. The correct work function is indicated by LED. Protections against: a short circut SCP, an overload OLP, a surge. The module will check the alarm installations, CCTV systems. An additional advantage is that by using the divider can reduce and arrange the amount of power cables in the installation. The module board was placed in a sturdy plastic housing. The flap edge sealing gasket is placed by the intrusion into the water. The housing fastened to the base by means of screws (two holes Ø4mm) and the hose clamp to the mast. Supply voltage range: 10-30V DC. Output voltage: Uout = Uin. Power consumption: 8mA - 70mA. Power inputs: 1x the DC 5.5/2.1, 1x screw terminals. Number of outputs: 8x screw terminals. Operating temperature: -10°C..40°C. Size: 126 x 78+16 x 42 mm.

Fuse module, a power distribution module. The module enables the power supply section 8 independent channels. Short circuit, sabotage or other attempt to damage the terminal does not affect the operation of other devices connected to the same power source. The correct work function is indicated by LED. Protections against: a short circut SCP, an overload OLP, a surge. The module will check the alarm installations, CCTV systems. An additional advantage is that by using the divider can reduce and arrange the amount of power cables in the installation. The module board was placed in a sturdy plastic housing. The flap edge sealing gasket is placed by the intrusion into the water. The housing fastened to the base by means of screws (two holes Ø4mm) and the hose clamp to the mast. Supply voltage range: 10-30V DC. Output voltage: Uout = Uin. Power consumption: 8mA - 70mA. Power inputs: 1x the DC 5.5/2.1, 1x screw terminals. Number of outputs: 8x screw terminals. Operating temperature: -10°C..40°C. Size: 126 x 78+16 x 42 mm.

Fuse module, a power distribution module. The LB1P/1x3.15A/1.5/FTA/230V fuse module is designed to protect the power supply circuits requiring a voltage of 230V AC. It is fitted with the one input for power supply and one output is equipped with short circuit protection (SCP), melting fuse (T 3.15Amp). The module is adapted for connection of cables with a maximum cross section of 1,5mm². The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. supply voltage range: 230V DC. Output voltage: equal to supply voltage. Power inputs: 1x screw connection 0.51÷1.63 (AWG 24-14) 0.2 ÷ 1.5mm². Number of outputs: 1x screw connection 0.51÷1.63 (AWG 24-14) 0.2 ÷ 1.5mm². Operating temperature: -10°C..50°C. Size: 60 x 43 x 40 mm.

Fuse module, a power distribution module. The LB4/4x0.5A/2.5/AW/R fuse module is designed for power distribution in low-voltage systems requiring voltage of 10V÷30V DC or 10V÷24V AC (e.g. buffer power supply, transformer etc.). It is fitted with the IN input for power supply and 4 independently protected AUX1÷AUX4 power supply outputs. Each AUX output is equipped with short circuit protection (SCP): melting fuse F 0.5A or PTC 0.5A polymer fuse (the possibility of using 1A fuses, not supplied) as well as with overvoltage protection - varistors. Output state is indicated by 4 L1 ÷ L4 LEDs. Fuse failure is indicated by turning off the appropriate LED: L1 for AUX1, L2 for AUX2 etc. Additionally, in the case of failure, the FPS output (Hi-Z state) and the Lfps LED are switched on. The FPS output can be used for remote control of a module e.g. external optical indication. The module is adapted for connection of cables with a maximum cross section of 2.5mm². Protections against: a short circut SCP, an overload OLP, a surge. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. supply voltage range: 10-30VDC / 10-24VAC. Output voltage: Uaux = Uin ( equal to supply voltage ). Power consumption: (1) 15mA-42mA 10-30V DC, (2) 37mA-42mA 10-24V AC. Power inputs: 1 (IN terminals) – max. 2.5mm² cable. Number of outputs: 4 (AUX terminals) – max. 2.5mm² cable. Fuse: 4x F 0.5Amp fuse or PTC 0.5Amp (the possibility of using 1Amp fuses, not supplied). Operating temperature: -10°C..50°C. Dimensions: 125 x 43 x 32 mm.

Fuse module with enclosure. The LBC5 fuse module is designed for power distribution in CCTV systems requiring the voltage in the range 10V- 30V DC. It is equipped with two power inputs: screw connection and DC jack 5.5/2.1 and five AUX1 ÷ AUX5 power outputs independently protected with 1A polymer fuses. The module is equipped with J1÷J5 jumpers disconnecting the power supply at the AUX1 ÷ AUX5 outputs ("+" terminal) PTC fuse activation is indicated by switching off the corresponding LED of the module: L1 for AUX1, L2 for AUX2 etc. Additionally, the module's input is protected by a varistor, protecting the power supply against surges in the power supply system. Protections against: a short circut SCP, an overload OLP, a surge. Mounting options: wall mounting – mounting screws x 2, mounting on a mast - hose clamp. Voltage range: 10-30VDC. Mounting options: wall mounting – mounting screws x 2, mounting on a mast - hose clamp. Power consumption: 5mA - 50mA. Power inputs 2: DC jack 5.5/2.1 or screw connection. Number of outputs: 5 (AUX terminals). Fuse: 5x1Amp – PTC. Operating temperature: -10°C..40°C. Dimensions: 150 x 94 x 42 mm.

Fuse module, a power distribution module. The LB4/4x2A/2.5/FTA fuse module is designed for power distribution in low-voltage systems requiring voltage of 10V÷30V DC. It is fitted with the IN input for power supply and 4 AUX1÷AUX4 power supply outputs independently protected with 2A fuses. Fuse activation is indicated by switching off the appropriate LED: L1 for AUX1, L2 for AUX2 etc. Additionally, each output is protected with a varistor protecting the power supply and receivers against surges in the supply system. The module is adapted for connection of wires with a maximum cross-section of 2.5mm². Protections against: a short circut SCP, an overload OLP, a surge. he module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. Supply voltage range: 10-30VDC. Output voltage: Uaux = Uin ( equal to supply voltage ). Power consumption: 5mA-30mA 10-30V DC. Power inputs: 1 (IN terminals) – max. 2.5mm² cable. Number of outputs: 4 (AUX terminals) – max. 2.5mm² cable. Fuse: 4x2Amp TOPIK. Operating temperature: -10°C..50°C. Dimensions: 80 x 43 x 30 mm.

Fuse module with enclosure. The LBC5 fuse module is designed for power distribution in CCTV systems requiring the voltage in the range 10V ÷ 30V DC. It is equipped with two power inputs: screw connection and DC jack 5.5/2.1 and five AUX1 ÷ AUX5 power outputs independently protected with 1A melting fuses. PTC fuse activation is indicated by switching off the corresponding LED of the module: L1 for AUX1, L2 for AUX2 etc. Additionally, the module's input is protected by a varistor, protecting the power supply against surges in the power supply system. Protections against: a short circut SCP, an overload OLP, a surge. Mounting options: wall mounting – mounting screws x 2, mounting on a mast - hose clamp. voltage range: 10-30VDC. Mounting options: wall mounting – mounting screws x 2, mounting on a mast - hose clamp. Power consumption: 5mA - 50mA. Power inputs 2: DC jack 5.5/2.1 or screw connection number of outputs: 5 (AUX terminals). Fuse: 5x1A – TOPIK. Operating temperature: -10°C..40°C. Dimensions: 150 x 94 x 42 mm.

Fuse module, a power distribution module. The module enables the power supply section 4 independent channels. Short circuit, sabotage or other attempt to damage the terminal does not affect the operation of other devices connected to the same power source. The correct work function is indicated by LED. Protections against: a short circut SCP, an overload OLP, a surge. The module will check the alarm installations, CCTV systems. An additional advantage is that by using the divider can reduce and arrange the amount of power cables in the installation. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. Supply voltage range: 10-30V DC. Output voltage: Uout = Uin. Power consumption: 5mA - 60mA. Power inputs: 1x the DC 5.5/2.1, 1x screw terminals. Number of outputs: 4x screw terminals. Operating temperature: -10°C..50°C. Size: 80 x 43 x 21 mm. Protection type: F0.5Amp - fuse.

Fuse module, a power distribution module. The LB5/5x0.5A/2.5/AW fuse module is designed for power distribution in low-voltage systems requiring voltage of 10V÷30V DC or 10V÷24V AC (e.g. buffer power supply, transformer etc.). It is fitted with the IN input for power supply and 5 independently protected AUX1÷AUX5 power supply outputs. Each AUX output is equipped with short circuit protection (SCP): melting fuse F 0.5A or PTC 0.5A polymer fuse (the possibility of using 1A fuses, not supplied) as well as with overvoltage protection - varistors. Output state is indicated by 5 L1 ÷ L5 LEDs. Fuse failure is indicated by turning off the appropriate LED: L1 for AUX1, L2 for AUX2 etc. Additionally, in the case of failure, the FPS output (Hi-Z state) and the Lfps LED are switched on. The FPS output can be used for remote control of a module e.g. external optical indication. The module is adapted for connection of cables with a maximum cross section of 2.5mm². Protections against: a short circut SCP, an overload OLP, a surge. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. supply voltage range: 10-30VDC / 10-24VAC. Output voltage: Uaux = Uin ( equal to supply voltage ). Power consumption: (1) 6mA-41mA 10-30V DC, (2) 10mA-32mA 10-24V AC. Power inputs: 1 (IN terminals) – max. 2.5mm² cable. Number of outputs: 5 (AUX terminals) – max. 2.5mm² cable. Fuse: 5x F 0.5Amp fuse or PTC 0.5Amp (the possibility of using 1Amp fuses, not supplied). Operating temperature: -10°C..50°C. Dimensions: 150 x 43 x 30 mm.

Fuse module, a power distribution module. The LB8/8x1.5A/2.5/FTA fuse module is designed for power distribution in low-voltage systems requiring voltage of 10V÷30V DC or 10V÷24V AC (e.g. buffer power supply, transformer etc.). It is fitted with 2 power inputs and 8 independent power paths protected with 1.5A fuses. Fuse activation is indicated by switching off the appropriate LED: L1 for AUX1, L2 for AUX2 etc. Additionally, each output is protected with a varistor protecting the power supply and receivers against surges in the supply system. The module is adapted for connection of cables with a maximum cross-section of 2.5mm². Protections against: a short circut SCP, an overload OLP, a surge. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. supply voltage range: 10-30VDC / 10-24VAC. Output voltage: Uaux = Uin ( equal to supply voltage ). Power consumption: 8mA-60mA 10-30V DC. Power inputs: 2 (IN terminals) – max. 2.5mm² cable. Number of outputs: 8 (AUX terminals) – max. 2.5mm² cable. Fuse: 8x1.5Amp - TOPIC. Operating temperature: -10°C..50°C. Dimensions: 144 x 43 x 26 mm.

Fuse module, a power distribution module. The module enables the power supply section 8 independent channels. Short circuit, sabotage or other attempt to damage the terminal does not affect the operation of other devices connected to the same power source. The correct work function is indicated by LED. Protections against: a short circut SCP, an overload OLP, a surge. The module will check the alarm installations, CCTV systems. An additional advantage is that by using the divider can reduce and arrange the amount of power cables in the installation. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. Supply voltage range: 10-30V DC. Output voltage: Uout = Uin. Power consumption: 5mA - 60mA. Power inputs: 1x the DC 5.5/2.1, 1x screw terminals. Number of outputs: 8x screw terminals. Operating temperature: -10°C..50°C. Size: 124 x 43 x 21 mm. Protection type: PTC 0.5Amp - polymer fuse.

Fuse module, a power distribution module. The module enables the power supply section 8 independent channels. Short circuit, sabotage or other attempt to damage the terminal does not affect the operation of other devices connected to the same power source. The correct work function is indicated by LED. Protections against: a short circut SCP, an overload OLP, a surge. The module will check the alarm installations, CCTV systems. An additional advantage is that by using the divider can reduce and arrange the amount of power cables in the installation. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. Supply voltage range: 10-30V DC. Output voltage: Uout = Uin. Power consumption: 5mA - 60mA. Power inputs: 1x the DC 5.5/2.1, 1x screw terminals. Number of outputs: 8x screw terminals. Operating temperature: -10°C..50°C. Size: 124 x 43 x 21 mm. Protection type: PTC 0.3Amp - polymer fuse.

Fuse module, a power distribution module. The LB2/2x2Amp/2.5/FTA fuse module is designed for power distribution in low-voltage systems requiring voltage of 10V÷30V DC or 10V÷24V AC (e.g. buffer power supply, transformer etc.). It is fitted with the IN input for power supply and 2 independent power paths protected with 2A fuses. Fuse activation is indicated by switching off the appropriate LED: L1 for AUX1, L2 for AUX2 etc. Additionally, each output is protected with a varistor protecting the power supply and receivers against surges in the supply system. The module is adapted for connection of wires with a maximum crosssection of 2.5mm². Protections against: a short circut SCP, an overload OLP, a surge. Supply voltage range: 10-30VDC / 10-24VAC. Output voltage: Uaux = Uin ( equal to supply voltage ). Power consumption: 3mA-20mA 10-30V DC. Power inputs: 1 (IN terminals) – max. 2.5mm² cable. Number of outputs: 2 (AUX terminals) – max. 2.5mm² cable. Fuses: 2x2Amp - TOCPI. Operating temperature: -10°C..50°C. Dimensions: 60 x 43 x 26 mm.

Fuse module, a power distribution module. The module enables the power supply section 8 independent channels. Short circuit, sabotage or other attempt to damage the terminal does not affect the operation of other devices connected to the same power source. The correct work function is indicated by LED. Protections against: a short circut SCP, an overload OLP, a surge. The module will check the alarm installations, CCTV systems. An additional advantage is that by using the divider can reduce and arrange the amount of power cables in the installation. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. Supply voltage range: 10-30V DC. Output voltage: Uout = Uin. Power consumption: 9mA - 60mA. Power inputs: 1x the DC 5.5/2.1, 1x screw terminals. Number of outputs: 8x screw terminals. Operating temperature: -10°C..50°C. Size: 124 x 43 x 21 mm. Protection type: F0.5Amp - fuse.