Fuse module, a power distribution module. The module enables the power supply section 8 independent channels. Short circuit, sabotage or other attempt to damage the terminal does not affect the operation of other devices connected to the same power source. The correct work function is indicated by LED. Protections against: a short circut SCP, an overload OLP, a surge. The module will check the alarm installations, CCTV systems. An additional advantage is that by using the divider can reduce and arrange the amount of power cables in the installation. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. Supply voltage range: 10-30V DC. Output voltage: Uout = Uin. Power consumption: 5mA - 60mA. Power inputs: 1x the DC 5.5/2.1, 1x screw terminals. Number of outputs: 8x screw terminals. Operating temperature: -10°C..50°C. Size: 124 x 43 x 21 mm. Protection type: PTC 1.0Amp - polymer fuse.

Fuse module, a power distribution module. The module enables the power supply section 4 independent channels. Short circuit, sabotage or other attempt to damage the terminal does not affect the operation of other devices connected to the same power source. The correct work function is indicated by LED. Protections against: a short circut SCP, an overload OLP, a surge. The module will check the alarm installations, CCTV systems. An additional advantage is that by using the divider can reduce and arrange the amount of power cables in the installation. The module board is mounted on a plastic base plate, which can be mounted to a flat substrate by means of two screws ø3mm or integrated adhesive tape. Supply voltage range: 10-30V DC. Output voltage: Uout = Uin. Power consumption: 5mA - 30mA. Power inputs: 1x the DC 5.5/2.1, 1x screw terminals. Number of outputs: 4x screw terminals. Operating temperature: -10°C..50° C. Size: 80 x 43 x 21 mm. Protection type: PTC 1.0Amp - polymer fuse.

The AWZ63 battery controller is designed for monitoring the status of the (Capacity 4x7÷18Ah/12V (SLA)) 4 batteries pack based on the measurements of resistance, continuity of the batteries circuit, voltage and the charge level. It is also protected against reverse connection and short circuit in the charging circuit. In the case of failure, a LED light is activated, which is accompanied by switching of relay contacts and acoustic indication. Destination: To monitor condition of battery/batteries by measuring resistance, continuity of the battery/batteries circuit, voltage and charge level. Short circuit protection and reverse battery connection. Acoustic indication of failure, LED diode and switching relay on. Input: BAT – terminals for connecting external batteries. Output: PSU – terminals for connecting uninterruptible power supply unit (BAT output of power supply). Maximum current: 5Amp. Fuse type: glass fuse – 1x7,5Amp. Battery: 4x7÷18Ah. Technical outputs relay type: ALARM – collective failure. Acoustic indication of failure – BUZZER – possibility of switching on / off. Mounting dimensions: W=108, H=38, L=80 [+/– 2mm].

The AWZ632 battery controller is designed for monitoring the status of the (Capacity: 7÷65Ah/12V (SLA)) battery pack based on the measurements of resistance, continuity of the battery circuit, voltage, and the charge level. It is also protected against reverse connection and short circuit in the charging circuit. In the case of failure, a LED light is activated, which is accompanied by switching of relay contacts and acoustic indication. Destination: To monitor condition of battery/batteries by measuring resistance, continuity of the battery/batteries circuit, voltage and charge level. Short circuit protection and reverse battery connection. Acoustic indication of failure, LED diode and switching relay on. Input: BAT – terminals for connecting external batteries. Output: PSU – terminals for connecting uninterruptible power supply unit (BAT output of power supply). Maximum current: 20Amp. Fuse type: glass fuse – 1x25Amp. Battery: 1x7÷65Ah. Technical outputs relay type: ALARM – collective failure. Acoustic indication of failure – BUZZER – possibility of switching on / off. Mounting dimensions: W=108, H=38, L=80 [+/– 2mm].

The AWZ633 battery controller is designed for monitoring the status of the (Capacity: 7÷40Ah/12V (SLA)) 2 batteries pack based on the measurements of resistance, continuity of the batteries circuit, voltage, and the charge level. It is also protected against reverse connection and short circuit in the charging circuit. In the case of failure, a LED light is activated, which is accompanied by switching of relay contacts and acoustic indication. Destination: To monitor condition of battery/batteries by measuring resistance, continuity of the battery/batteries circuit, voltage and charge level. Short circuit protection and reverse battery connection. Acoustic indication of failure, LED diode and switching relay on. Input: BAT – terminals for connecting external batteries. Output: PSU – terminals for connecting uninterruptible power supply unit (BAT output of power supply). Maximum current: 10Amp. Fuse type: glass fuse – 1x15Amp. Battery: 2x7÷40Ah. Technical outputs relay type: ALARM – collective failure. Acoustic indication of failure – BUZZER – possibility of switching on / off. Mounting dimensions: W=108, H=38, L=80 [+/- 2mm].

SmartCell 3.6V Lithium Battery.

SmartCell 6V 4Ah Battery.

Power supply for switches and media converters, input power 100-240VAC, output at 13.5VDC / 1.33A (18W).

Power supply for switches and media converters, input power 100-240VAC, output at 13.5VDC / 1.33A (18W).

Intended use: The RS485-ETHERNET interface is a device intended for converting signals between the RS485 bus and the Ethernet network and dedicated for working with power supply units of the EN54C-LCD group connected to LAN/WAN network. To work correctly, the device requires external power supply within the range of 10÷30V DC e.g. drawn from a PSU of the PSBEN / EN54 series. The physical connection is safe due to embeded galvanic isolation. The device is mounted in a hermetic enclosure that protects it against adverse environmental conditions. Power supply: 10÷30VDC. TTL transmission’s speed: 115200 bauds, with parity check. LAN transmission’s speed: 10/100Mbps (auto-negotation). Dimensions: 121 x 81 x 60 [mm]. Works with the PowerSecurity programming software. Embedded web server for configuration.

Intended use: The RS485-ETHERNET interface is a device intended for converting signals between the RS485 bus and the Ethernet network and dedicated for working with power supply units of the PSBEN (Black Power) / EN54 (Red Power) group connected to LAN/WAN network. To work correctly, the device requires external power supply within the range of 10÷30V DC e.g. drawn from a PSU of the PSBEN / EN54 series. The physical connection is safe due to embeded galvanic isolation. The device is mounted in a hermetic enclosure that protects it against adverse environmental conditions. Power supply: 10÷30VDC. TTL transmission’s speed: 115200 bauds, with parity check. LAN transmission’s speed: 10/100Mbps (auto-negotation). Dimensions: 121 x 81 x 60 [mm]. Works with the PowerSecurity programming software. Embedded web server for configuration.

Intended use: The RS485-TTL ”INTR” interface enables connecting of the PSU of the PSBEN (Black Power) / EN54 (Red Power) series to the RS485 bus remaining galvanic isolation. The communication in the RS485 bus is due to a two-way channel, differential in a half-duplex system where transmitting and receiving data is alternate. Power supply: 5V DC (max.30mA). Transmission’s speed: Max. 115200 bauds, with parity check. Dimensions: 63 x 50 x 20 [mm]. Warranty: 5 years form the date of production. Works with the PowerSecurity programming software.

Intended use: The RS485-TTL ”INTR” interface enables connecting of the PSU of the EN54C-LCD series to the RS485 bus remaining galvanic isolation. The communication in the RS485 bus is due to a two-way channel, differential in a half-duplex system where transmitting and receiving data is alternate. Power supply: 5V DC (max.30mA). Transmission’s speed: Max. 115200 bauds, with parity check. Dimensions: 63 x 50 x 20 [mm]. Warranty: 5 years form the date of production. Works with the PowerSecurity programming software.

Intended use: The ETHERNET interface is a device intended for connecting the power supplies of the EN54C-LCD series with a PC in the Ethernet network. The PowerSecurity system enables a remote monitoring of the parameters through a cyclical preview of the current status of the PSU, reading of the event history, preview of current and voltage charts and a remote battery test. Power supply: 5V DC(max. 0,95W) from the serial outlet of the PSU. TTL transmission’s speed: 115200 bauds, with parity check. LAN transmission’s speed: 10/100Mbps (auto-negotation). Dimensions: 63 x 50 x 24 [mm]. Works with the PowerSecurity programming software. Embedded web server for configuration.

Intended use: The ETHERNET interface is a device intended for connecting the power supplies of the PSBEN (Black Power) / EN54 (Red Power) series with a PC in the Ethernet network. The PowerSecurity system enables a remote monitoring of the parameters through a cyclical preview of the current status of the PSU, reading of the event history, preview of current and voltage charts and a remote battery test. Power supply: 5V DC(max. 0,95W) from the serial outlet of the PSU. TTL transmission’s speed: 115200 bauds, with parity check. LAN transmission’s speed: 10/100Mbps (auto-negotation). Dimensions: 63 x 50 x 24 [mm]. Works with the PowerSecurity programming software. Embedded web server for configuration.

Voltage: 20÷30VDC. Power supply output: 4x0,5Amp. Number of inputs/outputs: 1/4. Control input: INPUT – parametric (2x4,7k?). Protections: OLP*. Technical outputs – relay: PSU – parametric input failure INPUT. LED indication. Mounting options: tapping screws x 2. Dimensions: L=150 W=52,5 H=27 [+/-2mm]. Notes: dedicated for power supplies of EN54C / EN54M, sequentially switching of receivers, with a delay of 100 ms.

Intended use: The USB-TTL ”INTU” interface enables local connection of a PC with a PSU of the PSBEN (Black Power) / EN54 (Red Power) series. The interface is recognised by the computer"s operating system as a virtual COM port. To make a connection, no additional devices are required. Power supply: 5V DC(max.25mA) from the computer’s USB port. Transmission’s speed: Max. 115200 bauds, with parity check. Compliance of the USB interface: USB 1.1USB 2.0 (Full Speed). Dimensions: 57 x 32 x 25 [mm]. Length of the PSU wire: 1,5m. Length of the USB wire: 1,7m. Works with the PowerSecurity programming software.

Destination: set intended to surface mounting power supply units series EN54C. Dimensions: 84 x 26 mm. Included: brackets – 4 pcs, screw set M8x16 – 4 pcs (screw, steel washer, spring washer, hex nut).

Voltage: 20÷30VDC. Power supply output: 4x0,5Amp. Number of inputs/outputs: 2/4. Protections: SCP*. Technical outputs – relay: PSU – indication of fuse activation. LED indication. Mounting options: tapping screws x 2. Dimensions: L=150 W=52,5 H=27 [+/-2mm]. Notes: replacement fuses: F0,5Ax2 included, dedicated for power supplies of EN54C / EN54M.

Voltage: 20÷30VDC. Power supply output: 8x0,5Amp. Number of inputs/outputs: 1/8. Control input: INPUT – parametric (2x4,7k?). Protections: OLP*. Technical outputs – relay: PSU – parametric input failure INPUT. LED indication. Mounting options: tapping screws x 2. Dimensions: L=150 W=52,5 H=27 [+/-2mm]. Notes: dedicated for power supplies of EN54C / EN54M, sequentially switching of receivers, with a delay of 100 ms.

Fuse for EN54-4 power supply units. Dimensions: 150 x 45 x 32 mm, input voltage: 20÷30 VDC, number of outputs: 8x0,5A, standard fuses, technical outputs: PSU – indication of fuse activation (open collector i relay type).

Destination: A set for optical indicationis designed for optical signaling in power supplies of EN54M series. Dimensions: 66 x 18 mm. Notes: included: modules + cable 0,45m.

Fuse for EN54-4 power supply units. Dimensions: 110.5 x 45 x 32 mm, input voltage: 20÷30 VDC, number of outputs: 4x0,5A, standard fuses, technical outputs: PSU – indication of fuse activation (open collector i relay type).

Voltage: 20÷30VDC. Power supply output: 8x0,5Amp. Number of inputs/outputs: 2/8. Protections: SCP*. Technical outputs – relay: PSU – indication of fuse activation. LED indication. Mounting options: tapping screws x 2. Dimensions: L=150 W=52,5 H=27 [+/-2mm]. Notes: replacement fuses: F0,5Ax2 included, dedicated for power supplies of EN54C / EN54M.