Flow detector for 80mm pipes (3") with clamp anchor and disc in red color. Dispose of an adjustable delay mechanism, with a maximum adjustment of 30 seconds and a double switched circuit with voltage-free contacts (C/NA/NC). Flow direction indicator and audible relay.

Flow detector for 65mm pipes (2,5") with clamp anchor and disc in red color. Dispose of an adjustable delay mechanism, with a maximum adjustment of 30 seconds and a double switched circuit with voltage-free contacts (C/NA/NC). Flow direction indicator and audible relay.

EN54/5 Thermal detector just as TMP2DA2S1A but with an activation range between 84ºC and 100ºC (Class C).

Self-healing thermal probe with activation range between 99ºC and 115ºC (Class D) mounted in a ATEX II 2G EEx-d IIC T6 box, with IP66 protection grade. Particularly suitable for installations with explosive atmospheres and exhaust ducts or zones with a presence of corrosive elements or condensing vapors. Appropriate for indoors and outdoors. Compatible with most of market conventional centrals and with HLSI analogical centrals through a zone module.

EN54/5 Thermal detector just as TMP2TOA2S1A but with a activation range between 84°C and 100°C (class C).

EN54/5 Self-healing Thermal Detector with activation range between 54ºC and 70ºC (Class A) mounted in a flameproof box, ATEX II 2G EEx-d IIC T6, with IP66 protection grade. Specially appropriate for installations with explosive atmospheres, dangerous materials warehouses and exhaust ducts or zones with presence of corrosive elements or condensing vapors. Appropriate for indoors and outdoors. Compatible with most of market conventional centrals and HLSI analogical centrals through a zone module. Complies with CPR construction product regulation.

Self-healing thermal probe with an activation range between 99ºC and 115ºC (Class D) mounted in a watertight aluminium box with IP66 protection grade. Compatible with most of market conventional centrals and HLSI analogical centrals through a zone module.

EN54/5 Self-healing thermal detector with activation range between 54ºC and 70ºC (Class A). Mounted in a watertight aluminium box with IP66 protection grade. Appropriate for indoors and outdoors. Compatible with most of market conventional centrals and HLSI analogical centrals through a zone module. Complies with CPR construction product regulation.

Analogue addressable photoelectronic sensors are plug-in type smoke sensors that combine a photoelectronic sensing chamber with addressable-analogue communications. These sensors are designed for open area protection and must only be connected to control panels that use a compatible proprietary analogue addressable communciation protocol for monitoring and control.

IP67 Conventional inclemency detectors, fixed temperature of 72ºC, Class BS (Ex II 3GD EEx nA II T5). Includes base with pipe input.

IP67 Conventional inclemency detectors, fixed temperature of 57ºC, Class A2S (Ex II 3GD EEx nA II T5). Includes base with pipe input.

IP67 Conventional inclemency detectors, fixed temperature of 117ºC, Class ES (Ex II 3GD EEx nA II T5). Includes base with pipe input.

Compact conventional thermovelocimetric detector with controller alarm indictaion with base and pipe supplements, watertight electronic and anti-theft module. Certified CPD in accordance with EN54 part 5 standards.

Wireless analogic optical smoke detector with integrated sounder, for Aritech™ analogical panels. Frequency 868Mhz. Includes base and batteries. It is powered by 6 AA batteries MN 1500 LR6, autonomy of up to 5 years. Dimensions: 146 x 84 mm. Certificates: CE and CPR (EN54 parts 3, 7 and 25).

Display interface module that allows to view the direction of the alarm detector.

The TC841E1019 Conventional Zone Interface module provides an interface between a zone of HONEYWELL® manufactured conventional type fire detection devices and an intelligent signalling loop. A single tri-colour LED indicates the status of the module. In normal conditions, the LED can be set by command from the control panel to blink green when the module is polled. In the case of a fire alarm on the conventional zone, the LED is switched on constant red by panel command. If a fault is detected on the conventional zone or the zone supply voltage drops below 18V, or a fault with the external power supply is signalled, the LED will blink yellow if enabled on the control panel. When a short circuit is detected on the loop to either side of the module, the LED is switched to show a constant yellow light.

The relay module is a looppowered device controlling an unsupervised double pole (one normally open, one normally closed) output suitable for managing 240V ac loads. The output relay is a bi-stable device, latching in the on or off state on command from the control panel. It is available in two versions: boxed, wall mount and 35mm ‘Top Hat’ DIN rail mount.

The TC809EA1035 monitor module can be installed in a single gang junction box directly behind the monitored unit. Its small size and light weight allow it to be installed without rigid mounting (see Figure 1). The TC809EA1035 is intended for use in intelligent, two-wire systems where the individual address of each module is selected using rotary decade switches. It provides a two-wire initiating circuit for normally open contact fire alarm and security devices.

This module provides dual channel monitoring of normally open contact fire alarm and supervisory devices, and also provides single pole changeover contacts for the control of auxiliary devices such as fire shutters. Three tri-colour LED's are provided to indicate the status of each channel. LED's A and B refer to the two input channels. Each LED can be set by panel command to pulse green each time the module channel is polled. In case of an alarm the panel can switch the red indicator on continuously. The Yellow LED is controlled by the module and blinks to indicate an open circuit on the input circuit. This fault indication is always overridden by a panel command to turn the red LED on. LED C refers to the output channel. The LED can be set by panel command to pulse green each time the channel is polled. The LED will be switched continuously on Green by command from the control panel when the relay contacts are in the energised state. The TC809E1068 relay contact ratings are 30VDC, 2Amp or 30VAC, 0.5Amp (Resistive load).

The TC810E1032 output module allows the control of auxiliary devices such as fire shutters or sounders. A single tri-colour LED indicates the status of the module. In normal conditions, the LED can be set by command from the control panel to blink green when the module is polled. When the control panel switches the relay to the energised state the LED can be set to continuous green. In the case of an open circuit or fault on the output circuit, the module will set the LED to blink yellow.

Provides single channel monitoring of normally open contact fire alarm and supervisory devices. The TC809E1050 has a single tri-colour green/red/yellow LED, which can be set by panel command to pulse green each time the module is polled. In case of an alarm the panel can switch the red indicator on continuously. The Yellow LED is controlled by the module and blinks to indicate an open circuit on the input circuit. This fault indication is overridden by a panel command to turn the red LED on.

Provides single channel monitoring of normally open contact fire alarm and supervisory devices. The TC809E1043 has a single tri-colour green/red/yellow LED, which can be set by panel command to pulse green each time the module is polled. In case of an alarm the panel can switch the red indicator on continuously. The Yellow LED is controlled by the module and blinks to indicate an open circuit on the input circuit. This fault indication is overridden by a panel command to turn the red LED on.

Supervised input wireless module and voltage-free output for Aritech™ analogical panels. Frequency 868 MHz. Occupies an analog address. It is powered by 6 AA batteries MN 1500 LR6, autonomy of up to 5 years. Dimensions 240 x 120 x 50 mm. Certificates: CE and CPR (EN54 parts 18 and 25).

In the event of short circuit on the detector loop the C-9503 Isolators either side of the loop will defect the problem and open circuit and isolates the faulty part of the loop, enabling other devises on the unaffected part of the loop to operate normally. The module will continue to monitor for the fault to be repaired, once the fault is cleared the isolator will automatically reinstate the effected part of the loop.