DI-9101E intelligent combination heat photoelectric smoke detector integrates photoelectric detection and fixed temperature and rate of rise detection technology by combining smoke sensor and semi-conductor heat sensor in mechanism and circuitry structure. Just because of the combination of smoke detection and heat detection, it not only overcomes the disadvantage that detectors using common infrared scattering technology are insensitive to black smoke with small particles, but also can pick up fire with obvious rise of temperature such as alcohol flame, thus extending its application range.

DB-01 Base is used to mount digital and innovation conventional smoke, heat and combination detectors as their conductive base. It’s made of flame-resistant plastic ABS. It features attractive appearance, novel structure and stable performance. Its flame class is V-0. During installation, you can easily fix the base before connecting cables, and then twist the detector onto the base.

DZ-03 Base is used to mount conventional and intelligent smoke, heat and combination detectors as their conductive base (C-9102, C-9103, I-9102, I-9103). It’s made of flame-resistant plastic ABS, which is a UL94 listed material. It features attractive appearance, novel structure and stable performance. Its flame class is V-0. During installation, you can easily fix the base before connecting cables, and then twist the detector onto the base.

DI-9102E Intelligent Photoelectric Smoke Detector is a new generation product, connected with intelligent fire alarm control panel to form fire alarm system. The detector turns on fire LED to indicate fire alarm condition and transmits the fire signal to the control panel. The detector is developed from sensing chamber by scattering theory. Besides stable performance and easy maintenance, the detector has the ability to endure dust contamination and environmental light. The detector utilizes drift compensation algorithm: When the environment is changing, such as dust accumulation, humidity and temperature changing, the detector can figure out these drift variation to make up for sensitivity, thus the amount of smoke needed to generate an alarm remains constant, irrespective of environmental conditions.

In loop type fire alarm system, it often occurs that partial short circuit of loop affects the whole system. C-9504E Base Mount Short Circuit Isolator can isolate the shorted circuit from the whole system to ensure normal operation of the remaining parts and locate the failed part by illuminating a yellow indicator. When the short circuit fault is cleared, the shorted part will be restored. The isolator is applicable to all loop type fire alarm systems, either Class A or Class B loop.

SmartCell I / O module, quick and easy to install and offers individual addressing on the SmartCell control panel. Two resistance monitored inputs, two potential free outputs, 868 MHz bi-directional communication and a tamper lock mechanism. Completely wireless communication with the panel.

Internal SmartCell communication module. Provides remote connection option for updates, SMS / email. For internal connection within the SmartCell control panel. Includes GSM antenna and SIM card. Requires annual SmartCell remote services contract SC-94-0001-99.

SmartCell wireless control panel without communication module (24V DC). Quick and easy to install, compact design with 80-character OLED display. Supports internal communications card for connection of SmartCell services.

SmartCell wireless control panel without communication module (230V AC). Quick and easy to install, compact design with 80-character OLED display. Supports internal communications card for connection of SmartCell services.

The EMS SC-71-1201-0001 is the test / demo kit for use with the EMS SmartCell wireless fire alarm system.

Addressable zone supervision module for interfacing with a zone of up to 31 wireless devices. Includes isolator. It acts as an interface between the control panel and Fusion's wireless field devices. It transfers the wireless data from the radio signal to the wired protocol both to and from the control panel, allowing you to communicate seamlessly with these devices. It can be used with the 2X fire panel. Requires 24 Vdc power supply. IP54. Dimensions 270x205x75mm. Certificates: CE and CPR (EN54 parts 17, 18 and 25).

Bluetooth® UHF RFID reader. Designed to read and write to the new range of addressable fire alarm field devices. Designed to read UHF Gen2 tags and communicate via Bluetooth with your iPhone, Android or Windows Mobile. Works with iOS, Windous Mobile, Windous Phone 8, WinCE, XP7, XP8, Andriod operating systems. Configurable through ASCII protocols that allow us to program standard operations between the tags and the readers so that we can integrate the reader into our application without doing native development.

Module with two supervised inputs and two voltage-free relay outputs or 2A at 24VDC for operations that require a 24Vdc power supply, discriminating the cut fault or short circuit in said line, occupying an address in the loop. It incorporates LED status indicator. IP65. Dimensions: 240x120x60mm. Certificates: CE and CPR (EN54 parts 18 and 25).

Keeps large fire doors open, improving building ventilation. It closes automatically in case of fire. Dimensions 195x205x45 mm. Certificates: CE and CPR (EN54 part 25, EN 1155, BS7273-4).

Keeps large fire doors open, improving building ventilation. It closes automatically in case of fire. Dimensions 195x205x45 mm. Certificates: CE and CPR (EN54 part 25, EN 1155, BS7273-4).

Detection and fire fighting panels programmable for the control of risk 1 (2 crossed detection zones) of any extinction installation through gas extinguishing systems. Direct inputs for stop, launching, pause pushbutton , pressure switch monitoring and outputs for pre-alarm sounders, lauching extinction signaller, open door control and lanching of extinction (Option solenoid or pyrotechnics). LED indicator for each extinction control output. Earth fault detection. E/S expandable through 2010-1-RB/SB card. 4A power supply. 2 levels sounders output. Auto/manual control and indicator through user interface. Certified CE and CPR (EN54-2, EN54-4, EN12094-1 for gas extinction). Requires 2 batteries, reference BS127N (Not included).

Detection and fire fighting panels programmable for the control of risk 1 (2 crossed detection zones and 1 free zone- programmable) of any extinction installation through gas extinguishing systems. Direct inputs for stop, launching, pause pushbutton , pressure switch monitoring and outputs for pre-alarm sounders, lauching extinction signaller, open door control and lanching of extinction (Option solenoid or pyrotechnics). LED indicator for each extinction control output. Earth fault detection. E/S expandable through 2010-1-RB/SB card. For network connection requires 2010-1-NB card. 4A power supply. 2 levels sounders output. Auto/manual control and indicator through user interface. Certified CE and CPR (EN54-2, EN54-4, EN12094-1 for gas extinction). Requires 2 batteries, reference BS127N (Not included).

Carbon monoxide detection panel of 4 zones, with two alarm levels. 3 relay outputs by zones (Two for extraction/ventialation control and one for general alarm). Indicator through carbon monoxide concentration display (Sensivity from 0 to 300ppm). Compatible with KM170 and KMD300 detectors. Rapid answering time. Up to 15 detectors by zone. Certified, in accordance with UNE 23-301-88, CE, WEEE and RoHS standards. 230VAC Power supply. Dimensions: 420 x 336 x 118 mm.

Carbon monoxide detection panel of 3 zones, with two alarm levels. 3 relay outputs by zones (Two for extraction/ventialation control and one for general alarm). Indicator through carbon monoxide concentration display (Sensivity from 0 to 300ppm). Compatible with KM170 and KMD300 detectors. Rapid answering time. Up to 15 detectors by zone. Certified, in accordance with UNE 23-301-88, CE, WEEE and RoHS standards. 230VAC Power supply. Dimensions: 420 x 336 x 118 mm.

Carbon monoxide detection panel of 1 zone, with two alarm levels. 3 relay outputs by zones (Two for extraction/ventialation control and one for general alarm). Indicator through carbon monoxide concentration display (Sensivity from 0 to 300ppm). Compatible with KM170 and KMD300 detectors. Rapid answering time. Up to 15 detectors by zone. Certified, in accordance with UNE 23-301-88, CE, WEEE and RoHS standards. 230VAC Power supply. Dimensions: 297 x 307 x 109 mm.

Carbon monoxide detection panel of 2 zones, with two alarm levels. 3 relay outputs by zones (Two for extraction/ventialation control and one for general alarm). Indicator through carbon monoxide concentration display (Sensivity from 0 to 300ppm). Compatible with KM170 and KMD300 detectors. Rapid answering time. Up to 15 detectors by zone. Certified, in accordance with UNE 23-301-88, CE, WEEE and RoHS standards. 230VAC Power supply. Dimensions: 297 x 307 x 109 mm.

The GST301 conventional gas extinguishing control panel is packed with unique features that you have come to expect from a GST product that have enabled us to become world recognized as a leading manufacturer in the fire detection industry. The system provides 3 fire detection zones, two of which are utilized for double knock gas extinguishing control, and a third Auxiliary fire detection zone for additional areas out side of the gas protected area. This Zone will operate as a normal fire detection zone and have no interaction with the gas release system. Primary and Standby cylinder key switch, that enables quick and easy transfer to the reserve cylinders, thus to ensure that the area can be left protected after an evacuation. The pre release gas countdown timer display on the panel to shows the amount of time left (in seconds) before the gas will be released, this is adjustable from 0- to 90 seconds, (all panels are sent factory set at 30 seconds delay).

The GST303 and GST306 addressable gas extinguishing control panel is packed with unique features that you have come to expect from a GST product that have enabled us to become world recognized as a leading manufacturer in the fire detection industry. The system provides up to 6 extinguish zones, connected directly on the addressable loop Auxiliary, the FACP that are able to control associated fire suppressant equipment to achieve automatic or manual control of gas release. It can also control gas release devices independent of the FACP. When the FACP is not working properly, it can still control extinguishing devices through emergency gas override control in field or Start and Stop keys on the control panel. This control panel can check the circuit and alarm when circuit is open or shorted.

Matching with conventional fire alarm control panel or addressable zone monitor unit, P-9907 Active End of Line Unit takes place of end-of-line resistor which is connected to the loop in traditional way. It resolves such problems as abnormal operation of the whole system and nuisance alarm because of inappropriate resistor.